Emc
Thread Starter
8th Gear
Joined: Apr 2020
Posts: 8
Likes: 0
Emc
Hi, i own a 1998 corvette and is searching for a emc (19332289). The car is very Hard to start and The enginelight is on. My local workshop says its probably the emc... But its nowhere to be found... What can i do? Any ideas?
Frustrating
Kenth
Frustrating
Kenth
Moderator, Tech Contributor
Joined: Sep 2013
Posts: 15,643
Likes: 4,082
From: Cape Coral, Florida
First off WELCOME to the Forum !!...do you mean ECM (Engine Control Module) ??...what kind of diagnostics did your shop perform ??...you can pull the "codes" through the DIC if you don't have a scan tool or maybe you have it written down...when you say "hard to start" do you mean it doesn't "turn over" or it turns over and cranks but takes some time to start ??...even with a code it still may require some diagnostics to figure out...you can NOT change parts just based on a code !!
Moderator, Tech Contributor
Joined: Sep 2013
Posts: 15,643
Likes: 4,082
From: Cape Coral, Florida
Ken, the P0342 is a cam position sensor DTC and its most likely the cause of the car being hard to start...the sensor is located behind the intake manifold and with that code I have no idea of why the shop said you need a new engine computer...the P1516 is related to the throttle control system !!
Melting Slicks
Joined: Feb 2001
Posts: 2,804
Likes: 358
From: Northville, MI
The "C" codes are the current ones, "H" codes occurred also in the past. The B 037 and 0446 are HVAC actuator problems and not engine, the P042 and 1516 are engine management codes. The P0342 is a CMO sensor and the 1516 is the TAC module problem-most likely the hard start problem. The C5 is a drive by wire (DBW) engine and (overly simplified version) the gas pedal send a signal to the TAC module to open and close the Throttle body. The throttle control signal does not correspond to the actual signal being sent. Have them check on the condition of the TAC module to start with. When the gas pedal module goes bad the car usually will not start.
Thread Starter
8th Gear
Joined: Apr 2020
Posts: 8
Likes: 0
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Moderator, Tech Contributor
Joined: Sep 2013
Posts: 15,643
Likes: 4,082
From: Cape Coral, Florida
Moderator, Tech Contributor
Joined: Sep 2013
Posts: 15,643
Likes: 4,082
From: Cape Coral, Florida
How do you know 100% you need an engine computer ??...you have a cam sensor DTC..I don’t think your shop is up on diagnostics...FEW are !!...ask them HOW they came to that diagnosis and what was checked...I’d like to hear it !!
Thread Starter
8th Gear
Joined: Apr 2020
Posts: 8
Likes: 0
Thanks
Moderator, Tech Contributor
Joined: Sep 2013
Posts: 15,643
Likes: 4,082
From: Cape Coral, Florida
I believe the ‘98 PCM’s are scarce as hens teeth and some send theirs in for repair...I think you should let that shop know that if it’s replaced and doesn’t fix the problem they will be paying for it and not you !!...good luck !!
Burning Brakes
Joined: Jul 2011
Posts: 996
Likes: 307
From: Southern Norway , Europe