Z06 Bauer Motorsports Build: WCCH All Pro 290, Solid Roller, ERL 454, 14:1 SCR - Page 16 - CorvetteForum - Chevrolet Corvette Forum Discussion

Go Back  CorvetteForum - Chevrolet Corvette Forum Discussion > C6 Corvette, 2005 - 2013 > C6 Corvette ZR1 & Z06
Reload this Page >

[Z06] Bauer Motorsports Build: WCCH All Pro 290, Solid Roller, ERL 454, 14:1 SCR

Notices
C6 Corvette ZR1 & Z06 General info about GMs Corvette Supercar, LS9 Corvette Technical Info, Performance Upgrades, Suspension Setup for Street or Track Advertisement
Sponsored by:
Sponsored by:

[Z06] Bauer Motorsports Build: WCCH All Pro 290, Solid Roller, ERL 454, 14:1 SCR

Old 10-07-2018, 08:59 AM
  #301  
jayyyw
CF Senior Member
 
Member Since: Jun 2015
Location: Austin Tx
Posts: 2,503
Thanked 229 Times in 211 Posts
Default

Getting closer!!
jayyyw is offline  
Old 10-08-2018, 01:35 AM
  #302  
HC Mechanic
CF Senior Member
 
HC Mechanic's Avatar
 
Member Since: Nov 2009
Location: California
Posts: 1,012
Thanked 26 Times in 24 Posts
Default

Originally Posted by josh b. View Post


just gonna send it
arrrrrr rah!!
HC Mechanic is offline  
Old 10-10-2018, 11:03 PM
  #303  
Josh B.
CF Senior Member
Thread Starter
 
Josh B.'s Avatar
 
Member Since: Nov 2014
Location: Murrieta, CA
Posts: 2,523
Thanked 495 Times in 372 Posts
Default

Oil pump and front cover are on. Finished the valve reliefs with some final sanding on the edges. Also finished the pass side coil relocation. Had to narrow up the overall width to make sure there’s room for the door swing. Dropped in the lifters, using a special grip as to not damage anything. Modified the LG airbox/ ram air scoop because it had been jutting out of the grill.













Last edited by Josh B.; 10-10-2018 at 11:17 PM.
Josh B. is online now  
Old 10-10-2018, 11:15 PM
  #304  
JesC6Z
CF Senior Member
 
Member Since: Mar 2018
Posts: 548
Thanks: 0
Thanked 55 Times in 49 Posts
Default

2 in the birth canal and 1 in the clay doh machine is the grip I see😂🤪. Nice progress bud none the less !!!
JesC6Z is offline  
Old 10-11-2018, 08:17 AM
  #305  
double06
CF Senior Member
 
Member Since: May 2006
Location: Potomac MD
Posts: 2,011
Thanked 50 Times in 49 Posts
Default

Head and manifold party are next.
double06 is offline  
Old 10-11-2018, 01:59 PM
  #306  
MTPZ06
CF Senior Member
Support Corvetteforum!
 
MTPZ06's Avatar
 
Member Since: Dec 2008
Location: Honolulu HI
Posts: 11,826
Thanked 1,058 Times in 940 Posts
Default

Man...grinding on pistons would scare the sh*t outta me.
MTPZ06 is offline  
Old 10-11-2018, 03:27 PM
  #307  
jayyyw
CF Senior Member
 
Member Since: Jun 2015
Location: Austin Tx
Posts: 2,503
Thanked 229 Times in 211 Posts
Default

I totally forgot to remind you to put the lifters in! Good thing you didn't, LOL!
jayyyw is offline  
Old 10-11-2018, 03:29 PM
  #308  
Josh B.
CF Senior Member
Thread Starter
 
Josh B.'s Avatar
 
Member Since: Nov 2014
Location: Murrieta, CA
Posts: 2,523
Thanked 495 Times in 372 Posts
Default

Originally Posted by jayyyw View Post
I totally forgot to remind you to put the lifters in! Good thing you didn't, LOL!
LOL, I was half serious too But all is well because I remembered.
Josh B. is online now  
The Following User Says Thank You to Josh B. For This Useful Post:
jayyyw (10-11-2018)
Old Yesterday, 02:45 AM
  #309  
Josh B.
CF Senior Member
Thread Starter
 
Josh B.'s Avatar
 
Member Since: Nov 2014
Location: Murrieta, CA
Posts: 2,523
Thanked 495 Times in 372 Posts
Default

Pushrods measured. Going to order some Manton dual tapered 7/16 pushrods. Headers are on. This was a major pain because the All Pros are drilled for 3/8-16 exhaust manifold bolts, so I had to team out the holes in the header flange. I used a stepped bit in an air ratchet in order to fit the right confines without removing the headers from the car.

Balancer is on.

Both coil brackets mounted.





Josh B. is online now  
Old Yesterday, 08:50 AM
  #310  
double06
CF Senior Member
 
Member Since: May 2006
Location: Potomac MD
Posts: 2,011
Thanked 50 Times in 49 Posts
Default

Getting there when do you think you will have it done? I know you got a few parts on order.
double06 is offline  
Old Yesterday, 08:51 AM
  #311  
double06
CF Senior Member
 
Member Since: May 2006
Location: Potomac MD
Posts: 2,011
Thanked 50 Times in 49 Posts
Default

Like the new cam sensor.
double06 is offline  
Old Yesterday, 09:01 AM
  #312  
FNBADAZ06
CF Senior Member
 
FNBADAZ06's Avatar
 
Member Since: Jun 2009
Posts: 5,605
Thanked 197 Times in 161 Posts
Default

Progress, buddy !!!! CAn't wait to see it fire up
FNBADAZ06 is offline  
The Following User Says Thank You to FNBADAZ06 For This Useful Post:
HC Mechanic (Yesterday)
Old Yesterday, 12:23 PM
  #313  
Jayfabs
CF Senior Member
 
Member Since: Nov 2016
Posts: 621
Thanked 58 Times in 53 Posts
Default

Getting close! Are u still having Matt tune the car?
Jayfabs is offline  
Old Yesterday, 12:35 PM
  #314  
Josh B.
CF Senior Member
Thread Starter
 
Josh B.'s Avatar
 
Member Since: Nov 2014
Location: Murrieta, CA
Posts: 2,523
Thanked 495 Times in 372 Posts
Default

Originally Posted by Jayfabs View Post
Getting close! Are u still having Matt tune the car?
Thanks man. No. After speaking to Ryne Cunningham about the car and my goals I decided to have him tune the car. Theres a couple niche things well be doing with the new combo that Ryne has experience with. Plus he is local and an awesome guy and you cant beat that.
Josh B. is online now  
The Following User Says Thank You to Josh B. For This Useful Post:
HC Mechanic (Yesterday)
Old Yesterday, 12:38 PM
  #315  
Josh B.
CF Senior Member
Thread Starter
 
Josh B.'s Avatar
 
Member Since: Nov 2014
Location: Murrieta, CA
Posts: 2,523
Thanked 495 Times in 372 Posts
Default

Originally Posted by double06 View Post
Getting there when do you think you will have it done? I know you got a few parts on order.
Im waiting on some parts. Hopefully sooner than later but you know how it goes. Ill order up my pushrods Monday. Probably route my oil feed lines to the valve covers for the spring squirters. Lots of -4 line and fittings to do that.
Josh B. is online now  
The Following User Says Thank You to Josh B. For This Useful Post:
HC Mechanic (Yesterday)
Old Yesterday, 01:45 PM
  #316  
HC Mechanic
CF Senior Member
 
HC Mechanic's Avatar
 
Member Since: Nov 2009
Location: California
Posts: 1,012
Thanked 26 Times in 24 Posts
Default

She’s coming along nicely Brother! Let me know if you need a hand with anything
HC Mechanic is offline  


Thread Tools
Search this Thread
Quick Reply: [Z06] Bauer Motorsports Build: WCCH All Pro 290, Solid Roller, ERL 454, 14:1 SCR


Sponsored Ads
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2018 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: