Rear Z06 splash guards write-up?
Melting Slicks
Joined: Feb 2005
Posts: 2,179
Likes: 97
From: Palm Coast, FL
Yeah, save yourself the trouble and heartaches and pay someone WHATEVER THEY WANT to install it, no matter what the cost! I tried to install one in the rear, screwed it up and had to buy another one at which time I had a local corvette shop do the install. Cost was based on time-time to bend over and grin and bear it-LOL. What took them hours(3-4) would have taken me the same number of days not to mention how many more I would have screwed up by cutting to much trying to make it fit properly. This way, if they screw up, THEY have to buy another one and get it right; not you.
Think real hard about this one...
Think real hard about this one...
Burning Brakes
Joined: Oct 2005
Posts: 1,131
Likes: 0
From: Dallas Texas
I agree. 21st Century Musclecars in Dallas did mine. Andy at 21CMC fabricated them so no holes had to be drilled in the body. All attachments are to inner fender and rear valance 
Last edited by midnite902; Apr 5, 2006 at 09:48 PM.
Team Owner
Joined: Jan 2004
Posts: 38,772
Likes: 621
From: Boston MA
St. Jude Donor '06-'07-'08,'12-'13
I have done 2 sets and to tell you the truth they were both different
You basically have to hand shape them and overall thak a 1/4 in off them.
Here are some pics of mine .
I am trying to writeup sort of an iinstall guide but they truely are custom.
I wish i could make a template and have these things mass produced by an injection moulding company.
You basically have to hand shape them and overall thak a 1/4 in off them.
Here are some pics of mine .
I am trying to writeup sort of an iinstall guide but they truely are custom.
I wish i could make a template and have these things mass produced by an injection moulding company.
Team Owner
Joined: Sep 2000
Posts: 31,727
Likes: 1
From: My anger management class pisses me off outside of Nashville
Cruise-In I Veteran
Cruise-In II Veteran
Cruise-In III Veteran
Cruise-In IV Veteran
St. Jude Donor '07
Originally Posted by S281ER238
whats part number for the rear flaps at fread beans
Team Owner
Joined: Sep 2000
Posts: 31,727
Likes: 1
From: My anger management class pisses me off outside of Nashville
Cruise-In I Veteran
Cruise-In II Veteran
Cruise-In III Veteran
Cruise-In IV Veteran
St. Jude Donor '07
Originally Posted by 99 torch red vette
ttt..
It can't be that hard to install these...
It can't be that hard to install these...
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Team Owner
Joined: Jan 2004
Posts: 38,772
Likes: 621
From: Boston MA
St. Jude Donor '06-'07-'08,'12-'13
Originally Posted by 99 torch red vette
ttt..
It can't be that hard to install these...
It can't be that hard to install these...
But it took me close to 4 hrs for both sides !
Le Mans Master
Joined: Feb 2005
Posts: 6,916
Likes: 1,428
From: Any City USA
Originally Posted by burtonbl103
I have done 2 sets and to tell you the truth they were both different
You basically have to hand shape them and overall thak a 1/4 in off them.
Here are some pics of mine .
I am trying to writeup sort of an iinstall guide but they truely are custom.
I wish i could make a template and have these things mass produced by an injection moulding company.
You basically have to hand shape them and overall thak a 1/4 in off them.
Here are some pics of mine .
I am trying to writeup sort of an iinstall guide but they truely are custom.
I wish i could make a template and have these things mass produced by an injection moulding company.
