QTEC Cutouts
Thread Starter
Intermediate
Joined: Jun 2006
Posts: 25
Likes: 0
QTEC Cutouts
Has anyone installed QTEC cutouts on their C6 . . . my C6 is new; will cutouts void my warranty?
Craig
QTEC website: http://www.quicktimeperformance.com/QTEC/
Craig
QTEC website: http://www.quicktimeperformance.com/QTEC/
Melting Slicks
Joined: Oct 2005
Posts: 2,586
Likes: 141
From: Palm Beach Florida
I like the concept, loud when you want it, NO DRONE! BUT BUT, NO One is using it on their vette! They should make it wireless, would make a much simpler install!
I am not sure which is better, also saw these on CF.
http://www.streetpro.us/
I am not sure which is better, also saw these on CF.
http://www.streetpro.us/
Last edited by rckt; Oct 11, 2006 at 09:06 PM.
Intermediate
Joined: Jan 2006
Posts: 36
Likes: 0
From: Salt Lake City Utah
It isn't a c6 by any means, but I run them on my daily driven T/A. At some point I became obsessed with keeping the car quiet. QTEC was completely the answer. Loud as hell when I want to get the Honda next to me to stop revving his engine; quiet enough to hear myself think when I don't.
Wireless would be nice, but these can be done with a good clean install.
Wireless would be nice, but these can be done with a good clean install.
Melting Slicks
Joined: Nov 2003
Posts: 2,312
Likes: 82
From: Ridgeland MS
St. Jude Donor '06-'07-'08-'09-'10-'11
I use the Quick Time cutouts on my 2005 C6. Loud Loud Loud when you want it and quiet with a Borla Touring System the rest of the time.
The cutouts face inward on each side of the transmission with the opener motors sticking up between the tranny and the tunnel (over the top of the exhaust pipe). My installer made some little turn-downs so that the exhaust doesn't blast into the rear center section.
They have been on my car for over 2 years and I have never had an issue with warranty or codes being thrown.
The cutouts face inward on each side of the transmission with the opener motors sticking up between the tranny and the tunnel (over the top of the exhaust pipe). My installer made some little turn-downs so that the exhaust doesn't blast into the rear center section.
They have been on my car for over 2 years and I have never had an issue with warranty or codes being thrown.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Top 10 C9 Corvette MUST-HAVES to Fix These C8 Generation Flaws!
Michael S. Palmer
10 Revolutionary 'Corvette Firsts' Most People Don't Know
Joe Kucinski
5 Reasons to Upgrade to an LS6-Powered Corvette; 5 Reasons to Stay LT2
Michael S. Palmer
Melting Slicks
Joined: Oct 2005
Posts: 2,586
Likes: 141
From: Palm Beach Florida
Originally Posted by dollarbill
I use the Quick Time cutouts on my 2005 C6. Loud Loud Loud when you want it and quiet with a Borla Touring System the rest of the time.
The cutouts face inward on each side of the transmission with the opener motors sticking up between the tranny and the tunnel (over the top of the exhaust pipe). My installer made some little turn-downs so that the exhaust doesn't blast into the rear center section.
They have been on my car for over 2 years and I have never had an issue with warranty or codes being thrown.
The cutouts face inward on each side of the transmission with the opener motors sticking up between the tranny and the tunnel (over the top of the exhaust pipe). My installer made some little turn-downs so that the exhaust doesn't blast into the rear center section.
They have been on my car for over 2 years and I have never had an issue with warranty or codes being thrown.
. Do you have any pics? Do they leak at all? Can they be placed at the end just before the muffler facing down? Thanks,
Gene
PS. Any sound clips?
Melting Slicks
Joined: Nov 2003
Posts: 2,312
Likes: 82
From: Ridgeland MS
St. Jude Donor '06-'07-'08-'09-'10-'11
Originally Posted by csp46
Thanks . . . have you had any warranty work after installing the cutouts?
Craig
Craig
I will take some pics and post the later.
Bill
Racer
Joined: Jan 2003
Posts: 400
Likes: 2
From: Haskell, NJ 973-513-9955
Guys if you have any pics of our cutouts on your C6 please send them to us. We would like to add to our site. We get many requests but do not have any pictures of them. And if anyone has like to make a video for us email me. I like to show off the videos on the website and at the SEMA show. Email us directly at sales@quicktimeperformance.com
Pro
Joined: Sep 2001
Posts: 539
Likes: 0
From: Corona CA
Guys if you have any pics of our cutouts on your C6 please send them to us. We would like to add to our site. We get many requests but do not have any pictures of them. And if anyone has like to make a video for us email me. I like to show off the videos on the website and at the SEMA show. Email us directly at sales@quicktimeperformance.com
I have a set of your competitors on my 70 BB Chevelle so it would be nice to see how yours stack up - I'm not real happy with brand D.
