C6 Power Steering(PS) Pump swap taking PS pump alternator bracket off car
#1
Melting Slicks
Thread Starter
Member Since: Nov 2005
Location: Houston 06 C6 Ysi SC 402 fgd TX
Posts: 2,345
Likes: 0
Received 2 Likes
on
2 Posts
C6 Power Steering(PS) Pump swap taking PS pump alternator bracket off car
Maybe its the 295 wide tires I run on the front that wipes out the Power steering pump... keep scrolling down for text between pictures.
I bought an aftermarket PS pump from TurnOne that regears the pump so it spins less. I swapped it for my burned up Delco that i sent back in for warranty. I have that brand new Delco one for sale.
http://forums.corvetteforum.com/c6-p...post1574651233
You will need a press/tool to take the pulley off the PS shaft making sure you measure to place the pulley precisely in the exact location it was. GM has you use that tool right on the car..since i do not have the tool, I had to take the pump off the car and take it to vettech in Houston for them to do the swap. unloosen belt tension-er. you can see that i have already used spacers to move the ABS unit away from the PS pulley.
There are 4 bolts that attach the PS/Alt bracket to the block. this pic shows how to reach the farthest and unloosen a little bit at a time.
on my setup i had to take the PS reservoir off too to get to the bracket bolts.
once the bracket is off Plug the steering column so no contaminants get into the system. the hose wraps completely around the steering column and is a PITA.
take the whole thing to your mechanic to have the power steering pump swapped. don't forget to re-install the outlet hose prior to re-installing the pulley.
car has a Z51 package with the PS cooler. I replaced with a JEGS double size and used same hoses. used zip ties for mounting
pfadt anti-sway bars and supercharger tubing routing to intercooler
crowded
reinstall in reverse order. make sure the belt is placed correctly and tightened to specs. No leaks so far
I bought an aftermarket PS pump from TurnOne that regears the pump so it spins less. I swapped it for my burned up Delco that i sent back in for warranty. I have that brand new Delco one for sale.
http://forums.corvetteforum.com/c6-p...post1574651233
You will need a press/tool to take the pulley off the PS shaft making sure you measure to place the pulley precisely in the exact location it was. GM has you use that tool right on the car..since i do not have the tool, I had to take the pump off the car and take it to vettech in Houston for them to do the swap. unloosen belt tension-er. you can see that i have already used spacers to move the ABS unit away from the PS pulley.
There are 4 bolts that attach the PS/Alt bracket to the block. this pic shows how to reach the farthest and unloosen a little bit at a time.
on my setup i had to take the PS reservoir off too to get to the bracket bolts.
once the bracket is off Plug the steering column so no contaminants get into the system. the hose wraps completely around the steering column and is a PITA.
take the whole thing to your mechanic to have the power steering pump swapped. don't forget to re-install the outlet hose prior to re-installing the pulley.
car has a Z51 package with the PS cooler. I replaced with a JEGS double size and used same hoses. used zip ties for mounting
pfadt anti-sway bars and supercharger tubing routing to intercooler
crowded
reinstall in reverse order. make sure the belt is placed correctly and tightened to specs. No leaks so far
Last edited by drivinfast; 07-10-2010 at 09:48 AM.
#2
Burning Brakes
Very timely -- thank you. I have a Turn One pump in my garage that I need to install and was hesitant because the GM service manual says you have to remove the ABS module and then do an ABS bleed. Very happy to see that that is not necessary.
#3
Former Vendor
Member Since: Jul 2008
Location: Oxnard SoCal www.aacorvette.com www.superchargersuperstore.com
Posts: 4,327
Likes: 0
Received 5 Likes
on
4 Posts
Very cool. You may want to fab up some brackets for the power steering cooler. Zip ties can break... usually at the most inopportune moment.
#4
Melting Slicks
Thread Starter
Member Since: Nov 2005
Location: Houston 06 C6 Ysi SC 402 fgd TX
Posts: 2,345
Likes: 0
Received 2 Likes
on
2 Posts
Just take your time, patience. i had to walk away a few times, get a beer. instead of breaking something...
thats what i swapped it with a TurnOne.
I did not mention the bleeding of the new fluid. once installed and with tires off still on jacks:
add fluid
turn steering wheel or rotors back and forth all the way 10 times or so.
then keep adding fluid until no bubbles appear....i never saw any at all, but thats the instructions.
then start car
turn steering wheel again same procedure
make sure no bubbles and reservoir stays same level
lower car
test drive.
#5
Melting Slicks
Thread Starter
Member Since: Nov 2005
Location: Houston 06 C6 Ysi SC 402 fgd TX
Posts: 2,345
Likes: 0
Received 2 Likes
on
2 Posts
I moved the stock one and got a larger one from where i had it installed previously
Last edited by drivinfast; 06-29-2010 at 02:15 PM. Reason: add pic
#6
Burning Brakes
Thanks again for posting this, Mark. I got my Turn One pump in today following your instructions. What a messy job (my old pump was leaking, so there was PS fluid and grime everywhere). Didn't have to crack open a single brake line so I am good to go!
Bert
Bert
#8
Burning Brakes
Follow Up -- Replace the Pressure Line!
After following these steps to replace my leaky pump, my leaks did not stay away for long. The C6 pressure line (between the pump and steering box) has a tendency to fail. Mine did and I had to do this entire repair a second time. What a pain.
GM has a newly designed pressure hose that is significantly different (and more costly) than the original C6 line -- I've heard it is more like the C5 hose design. I am hoping now not to see any power steering fluid underneath my car again for a long, long time.
GM has a newly designed pressure hose that is significantly different (and more costly) than the original C6 line -- I've heard it is more like the C5 hose design. I am hoping now not to see any power steering fluid underneath my car again for a long, long time.
#9
Racer
Member Since: Mar 2007
Location: Washington, D.C. District of Columbia
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
Looks like I'm going to need to do this repair. PS fluid all over the engine bay after spirited driving. Thanks for posting your progress with great pics. A few questions to help visualize this repair:
1. I haven't determined where the PS failure is. How did you tell if it was a pressure line failure or a pump failure (these seem to be the two main points of failure.)
2. Which TurnOne pump did you use the T40Y or the T40YZR1? EDIT: Just got off the phone with TurnOne, it's the T40Y.
3. Do you have a part number for the improved GM pressure line?
4. You mention "making sure you measure to place the pulley precisely in the exact location it was." What do you mean. pressing it to the same location on the pump shaft so the belt lines up? EDIT: For $70 TurnOne will install their custom pulley on their pump, so I don't need to worry about pulling/pressing tools and which provides easier access to the mounting bolts for future access.
5. What part number is your replacement oil cooler? I too have SC ducting in the same spot and I still have the monospring, so I need to get a larger cooler, but one that will fit in the stock location (although with all the hot air from the rad, I wonder if it is actually cooling the fluid?)
Thanks for any help. - adis
1. I haven't determined where the PS failure is. How did you tell if it was a pressure line failure or a pump failure (these seem to be the two main points of failure.)
2. Which TurnOne pump did you use the T40Y or the T40YZR1? EDIT: Just got off the phone with TurnOne, it's the T40Y.
3. Do you have a part number for the improved GM pressure line?
4. You mention "making sure you measure to place the pulley precisely in the exact location it was." What do you mean. pressing it to the same location on the pump shaft so the belt lines up? EDIT: For $70 TurnOne will install their custom pulley on their pump, so I don't need to worry about pulling/pressing tools and which provides easier access to the mounting bolts for future access.
5. What part number is your replacement oil cooler? I too have SC ducting in the same spot and I still have the monospring, so I need to get a larger cooler, but one that will fit in the stock location (although with all the hot air from the rad, I wonder if it is actually cooling the fluid?)
Thanks for any help. - adis
Last edited by Adis; 06-06-2011 at 06:09 PM.
#10
Burning Brakes
#11
Melting Slicks
Thread Starter
Member Since: Nov 2005
Location: Houston 06 C6 Ysi SC 402 fgd TX
Posts: 2,345
Likes: 0
Received 2 Likes
on
2 Posts
Looks like I'm going to need to do this repair. PS fluid all over the engine bay after spirited driving. Thanks for posting your progress with great pics. A few questions to help visualize this repair:
1. I haven't determined where the PS failure is. How did you tell if it was a pressure line failure or a pump failure (these seem to be the two main points of failure.) the power steering stopped working this is a Pain to replace, so make sure you diagnose correctly
2. Which TurnOne pump did you use the T40Y or the T40YZR1? EDIT: Just got off the phone with TurnOne, it's the T40Y.
3. Do you have a part number for the improved GM pressure line? answered
4. You mention "making sure you measure to place the pulley precisely in the exact location it was." What do you mean. pressing it to the same location on the pump shaft so the belt lines up? EDIT: For $70 TurnOne will install their custom pulley on their pump, so I don't need to worry about pulling/pressing tools and which provides easier access to the mounting bolts for future access.
5. What part number is your replacement oil cooler? I too have SC ducting in the same spot and I still have the monospring, so I need to get a larger cooler, but one that will fit in the stock location (although with all the hot air from the rad, I wonder if it is actually cooling the fluid?) I just ordered a larger one from summit or jegs. and used the clamps that came with it. I doubt you need one really.
Thanks for any help. - see highlighted
1. I haven't determined where the PS failure is. How did you tell if it was a pressure line failure or a pump failure (these seem to be the two main points of failure.) the power steering stopped working this is a Pain to replace, so make sure you diagnose correctly
2. Which TurnOne pump did you use the T40Y or the T40YZR1? EDIT: Just got off the phone with TurnOne, it's the T40Y.
3. Do you have a part number for the improved GM pressure line? answered
4. You mention "making sure you measure to place the pulley precisely in the exact location it was." What do you mean. pressing it to the same location on the pump shaft so the belt lines up? EDIT: For $70 TurnOne will install their custom pulley on their pump, so I don't need to worry about pulling/pressing tools and which provides easier access to the mounting bolts for future access.
5. What part number is your replacement oil cooler? I too have SC ducting in the same spot and I still have the monospring, so I need to get a larger cooler, but one that will fit in the stock location (although with all the hot air from the rad, I wonder if it is actually cooling the fluid?) I just ordered a larger one from summit or jegs. and used the clamps that came with it. I doubt you need one really.
Thanks for any help. - see highlighted
The following users liked this post:
Thebigblue (05-04-2016)
#12
Racer
Member Since: Mar 2007
Location: Washington, D.C. District of Columbia
Posts: 254
Likes: 0
Received 0 Likes
on
0 Posts
Thanks guys. That's an awesome rendering BTW, a lot clearer than the manual. where'd you get it? I was wondering why my pressure line was so long - now I know. The redesigned C5 line must have been installed from the factory on my 2010. This actually helps, since somehow my reservoir was overfilled by about 80 ml of fluid. I'm guessing a seal in the pump...
#14
Hey the pic for the long design is missing, but does anyone have a pic of it? I'm thinking it's the one in this pic:
Anyone able to confirm? So is this the hose you replace when installing a flip drive? Thanks!
#15
Le Mans Master
Good write up. One thing worth doing is cutting the holes on the power steering pump bracket into slots. You can then remove/replace it without fully removing the bolts which is a pain to do.
#16
Safety Car
Member Since: Aug 2006
Location: Apache Junction AZ
Posts: 4,347
Likes: 0
Received 22 Likes
on
18 Posts
BJK
Last edited by 07MontRedcp; 12-07-2013 at 01:31 PM.
#17
The following users liked this post:
joliett (09-19-2020)
#19
#20
Drifting
After following these steps to replace my leaky pump, my leaks did not stay away for long. The C6 pressure line (between the pump and steering box) has a tendency to fail. Mine did and I had to do this entire repair a second time. What a pain.
GM has a newly designed pressure hose that is significantly different (and more costly) than the original C6 line -- I've heard it is more like the C5 hose design. I am hoping now not to see any power steering fluid underneath my car again for a long, long time.
GM has a newly designed pressure hose that is significantly different (and more costly) than the original C6 line -- I've heard it is more like the C5 hose design. I am hoping now not to see any power steering fluid underneath my car again for a long, long time.
Now I have to go back in and replace the pump!