Mirror tap for Blendmount on 2015 C7
#181
Anyone install the wiring in a 2016 coupe? Is it the same as the 15' or 14'?
#184
Wow! What a pain in the butt. Got the cap off, separated the wiring from the cap...now the fun begins. Got the Red one in pin 2 purple and that took a bit but it finally went in. The Black ground i spent 1hour and can't get the little bastard in. Tried a jeweler's driver but still no luck. Totally sucks. Will give it one more try tomorrow.
So beware, your setup might be easy like what's been posted above or you might get one like mine, a total sob. Roll of the dice.
So beware, your setup might be easy like what's been posted above or you might get one like mine, a total sob. Roll of the dice.
#185
Drifting
Wow! What a pain in the butt. Got the cap off, separated the wiring from the cap...now the fun begins. Got the Red one in pin 2 purple and that took a bit but it finally went in. The Black ground i spent 1hour and can't get the little bastard in. Tried a jeweler's driver but still no luck. Totally sucks. Will give it one more try tomorrow.
So beware, your setup might be easy like what's been posted above or you might get one like mine, a total sob. Roll of the dice.
So beware, your setup might be easy like what's been posted above or you might get one like mine, a total sob. Roll of the dice.
#187
Wow! What a pain in the butt. Got the cap off, separated the wiring from the cap...now the fun begins. Got the Red one in pin 2 purple and that took a bit but it finally went in. The Black ground i spent 1hour and can't get the little bastard in. Tried a jeweler's driver but still no luck. Totally sucks. Will give it one more try tomorrow.
So beware, your setup might be easy like what's been posted above or you might get one like mine, a total sob. Roll of the dice.
So beware, your setup might be easy like what's been posted above or you might get one like mine, a total sob. Roll of the dice.
Took a 2nd shot at finishing this install and finally got the black wire slotted in. Tips of my fingers took a beating but the dam think is in. Another 5 to 10 minutes to get the cover back on...in never ends!!!
Checked the V1 again and it works fine.
So now, I think I've got everything all set. Take the V1 with the suction cups and mount it on the windshield (you KNOW where this is going) and the F'N wire doesn't reach the V1. I have to get a mirror V1 mount,
So, the 1st one I look at is over $100. You gotta be kidding me!!! So, then I found one company that's been around for ages and they have a mount for a little under $40.
#188
Instructor
Thank you for this thread!
Installed mine today, took my time. About an hour including adjusting the mount the way I wanted it.
Moved the purple & black wire with a small small screw driver as other have done.
Put some Slick 50 on the stab pins...no problem. Had to push little hard but nothing like some have posted.
Drilled a 3/16" hole out the back side of the harness cover for nice clean exit of the power wire.
Again thanks for this thread!
Installed mine today, took my time. About an hour including adjusting the mount the way I wanted it.
Moved the purple & black wire with a small small screw driver as other have done.
Put some Slick 50 on the stab pins...no problem. Had to push little hard but nothing like some have posted.
Drilled a 3/16" hole out the back side of the harness cover for nice clean exit of the power wire.
Again thanks for this thread!
#189
Instructor
#190
Drifting
#191
Broke my pins too, so removed 1/8" of sleeving from wire and wrapped detector lead wire and re taped. If Id done that to begin with could have been done in 10 minutes. Also of note, it does not power up unless car is started so if you test it by just going to accessory mode there is no power on the purple wire until car is started (at least in my 14 Z51).
#192
If anyone is about to get anything from blendmount you can get a 12.5% discount using this link:
http://blendmount.refr.cc/BNMXMW3
http://blendmount.refr.cc/BNMXMW3
#193
Drifting
I finally used a 4 wire telephone extension cord which I tucked away into the trim. Ran it down the passenger side A pillar and across under the dash. Connected to the power adapter with a double female connector. Now everything works great. On and off with the car and I can still use the smart cable mute function. All wiring is invisible and looks like professional install.
#194
Melting Slicks
Member Since: Feb 2006
Location: Simi Valley California
Posts: 2,545
Received 123 Likes
on
81 Posts
St. Jude Donor '06-'07-'10, '15. '22-'23
I finally used a 4 wire telephone extension cord which I tucked away into the trim. Ran it down the passenger side A pillar and across under the dash. Connected to the power adapter with a double female connector. Now everything works great. On and off with the car and I can still use the smart cable mute function. All wiring is invisible and looks like professional install.
#195
Burning Brakes
#196
Drifting
Mirror tap for Blendmount on 2015 C7
My cable is already concealed but this will show you the route I took. I ran it across the top of the windshield under the trim panels, down the passenger A pillar, under the dash. I ran the coiled smart cord under the trim panel next to the passenger seat and connected it to the extension line under the dash. Used a wire tie to tie everything off and tucked away under the dash.
Last edited by TNSQUIRE; 10-31-2015 at 08:42 PM.
The following users liked this post:
C6 MoneyPit (11-01-2015)
#197
Team Owner
I just finished installing my Blendmount V1 today. I had an unsuccessful attempt last weekend due to a loose RJ11 connector on the Mirror Tap cable. Michael from Blendmount refunded me for the cable as I ordered another to get it here ASAP and get it in before going back to work Monday. The second Mirror Tap I got also had a loose connector so I had to add some pin striping tape to the sides of the connector to tighten it up and maintain power to the V1. The various V1 RJ11 connectors I have all fit snugly in my V1 so I don't know why the difference in the Mirror tap connectors.
Anyway, all's well that ends well. It's mounted and working properly. Looks great.
Anyway, all's well that ends well. It's mounted and working properly. Looks great.
Last edited by Patches; 10-31-2015 at 10:39 PM.
The following users liked this post:
C6 MoneyPit (11-01-2015)
#198
Advanced
I'm using the standard Blendmount with my Escort 9500ix. I purchased a hard wired flat cable from Escort. This is the route I took. I ran it across the top of the windshield under the trim panels, down the passenger A pillar,along the door sill along the passenger side, under the carpet to the fuse box in the back of the car. I wired it to switched power so it turns off and on with the car. Couldn't be happier as all the wires are concealed.
#199
Melting Slicks
Member Since: Feb 2006
Location: Simi Valley California
Posts: 2,545
Received 123 Likes
on
81 Posts
St. Jude Donor '06-'07-'10, '15. '22-'23
My cable is already concealed but this will show you the route I took. I ran it across the top of the windshield under the trim panels, down the passenger A pillar, under the dash. I ran the coiled smart cord under the trim panel next to the passenger seat and connected it to the extension line under the dash. Used a wire tie to tie everything off and tucked away under the dash.
Attachment 47927255
Attachment 47927252
Attachment 47927254
Attachment 47927253
Attachment 47927255
Attachment 47927252
Attachment 47927254
Attachment 47927253
#200
Drifting
Thanks. The one thing I like about this method over the mirror tap is I can still use the mute function on the smart cord which is plugged into the pop up power adapter. These are the only two items you need.
Last edited by TNSQUIRE; 11-01-2015 at 09:25 PM.