question for those with simulation software???
Thread Starter
Racer
Joined: May 2000
Posts: 429
Likes: 0
From: chagrin falls,oh,usa
question for those with simulation software???
i am having the following engine installed next week. can anyone tell me what hp and torq this combo will have?
406 ci
trick flow twisted wedge heads and approximately 9.8:1 compression
super ram w 52 mm throttle body
1 5/8 long tube headers, into 2 3/4" borla off road exhaust - no cat
214*.486 lift intake; 218*.488 exhaust 108*ls
7 qt pan with diamond stripper windage tray
any help greatly appreciated
thanks
406 ci
trick flow twisted wedge heads and approximately 9.8:1 compression
super ram w 52 mm throttle body
1 5/8 long tube headers, into 2 3/4" borla off road exhaust - no cat
214*.486 lift intake; 218*.488 exhaust 108*ls
7 qt pan with diamond stripper windage tray
any help greatly appreciated
thanks
Thread Starter
Racer
Joined: May 2000
Posts: 429
Likes: 0
From: chagrin falls,oh,usa
Re: question for those with simulation software??? (johndezman)
thanks for the reply i appreciate the input. my "guess" was 370 hp and 450 ft/lbs - these "sound better" more exiting.
thanks again
thanks again
Le Mans Master
Joined: Feb 1999
Posts: 5,877
Likes: 1
From: Park Ridge IL
Re: question for those with simulation software??? (johndezman)
John,
I think you could stand to use a larger cam. 214/218 cam is pretty mild for a 406SR motor. I don't know if a roller cam is out of the questions, but it would be a nice upgrade as well. I think you could stand to use a cam with 220 to 230 degrees of duration while still maintaining a good idle/vacuum, and providing tremendous torque, probably around 500 lb ft.
I think you could stand to use a larger cam. 214/218 cam is pretty mild for a 406SR motor. I don't know if a roller cam is out of the questions, but it would be a nice upgrade as well. I think you could stand to use a cam with 220 to 230 degrees of duration while still maintaining a good idle/vacuum, and providing tremendous torque, probably around 500 lb ft.
Thread Starter
Racer
Joined: May 2000
Posts: 429
Likes: 0
From: chagrin falls,oh,usa
Re: question for those with simulation software??? (Monty)
thus far the converter will be left stock and i was concerned about idle and waiting at traffic signals.
also there's some "stealth" in mind so that the old stoplight grand prix goes my way!
i have a 224/240 "on the shelf" if i get a different converter next winter
also there's some "stealth" in mind so that the old stoplight grand prix goes my way!
i have a 224/240 "on the shelf" if i get a different converter next winter
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Le Mans Master
Joined: Oct 2001
Posts: 5,302
Likes: 2
From: Atlanta GA
Re: question for those with simulation software??? (johndezman)
I would highly recommend a roller cam motor. If monty would run the same motor, same dur., w/ a roller cam, you will probably gain a good 20 hp or more.