Ignition shield brackets question
Thread Starter
Melting Slicks
Joined: Mar 1999
Posts: 2,845
Likes: 2
From: Apex NC
Ignition shield brackets question
I want to add the original ignition shielding back to my smallblock '69. I have a pair of the vertical shields but nothing else, no brackets, etc. What do I need to purchase just to attach the distributor cover and the vertical shields?
In looking at my AIM, I see the brackets up at the distributor, but where do they bolt to on the intake? Where do the vertical shields attach at the lower end?
Thanks!
Shannon
In looking at my AIM, I see the brackets up at the distributor, but where do they bolt to on the intake? Where do the vertical shields attach at the lower end?
Thanks!
Shannon
Melting Slicks
Joined: Nov 2000
Posts: 2,112
Likes: 3
From: Kingston, TN
St. Jude Donor '06
Re: Ignition shield brackets question (sb69coupe)
The easiest way to answer this would be for you to look in one of the many vendor catalogs that picture these parts and their relationship to one another. The distributor cover brackets go under the rear intake manifold bolts. There are two plug wire holders that bolt to the lower portion of the block on each side that also have threaded holes for the vertical shielding wingnuts.
Melting Slicks
Joined: Dec 1999
Posts: 2,157
Likes: 0
From: Pensacola FLA
Re: Ignition shield brackets question (sb69coupe)
Hello Shannon,
I have all my ignition shielding attached on my small block. I'll check mine out tonight or tomorrow and get back with you.
I have all my ignition shielding attached on my small block. I'll check mine out tonight or tomorrow and get back with you.
Melting Slicks
Joined: Apr 2002
Posts: 2,103
Likes: 0
From: Tucson AZ
Re: Ignition shield brackets question (Mac)
I see someone on C3 forum posted a diagram of the ignition shields. My only wish would be for a larger version.
Melting Slicks
Joined: Dec 1999
Posts: 2,157
Likes: 0
From: Pensacola FLA
Re: Ignition shield brackets question (sb69coupe)
I crawled under my car and took a look. Here' what I found, on the driverside, as stated earlier, top shield is fastened to a bracket that is held in place by the back intake manifold bolt. This bracket also holds a 4 hole sparkplug wire grommet. The vertical shield is bolted to the side of the top shield box and bolted at the bottom to another bracket that holds another 4 wire sparkplug grommet. This bracket is fastened to the engine block.
On the passengerside, the topshield is also fastened to a bracket that is held in place by the back intake manifold bolt. This bracket holds a 4 hole spark plug wire grommet. The vertical shield is bolted to the side of the top shield box. The bottom of the vertical shield is bolted to a chrome exhaust shield which is held in place by two angle type brackets held in place by the exhaust manifold bolts. Hope this helps.
Melting Slicks
Joined: Dec 1999
Posts: 2,157
Likes: 0
From: Pensacola FLA
Re: Ignition shield brackets question (sb69coupe)
Shannon,
Checking out the shielding has reminded me of the need to pull my exhaust mainfolds and paint them with the por-15 gray exhaust manifold paint. I've been putting this off for awhile now.
Checking out the shielding has reminded me of the need to pull my exhaust mainfolds and paint them with the por-15 gray exhaust manifold paint. I've been putting this off for awhile now.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Top 10 C9 Corvette MUST-HAVES to Fix These C8 Generation Flaws!
Michael S. Palmer
10 Revolutionary 'Corvette Firsts' Most People Don't Know
Joe Kucinski
5 Reasons to Upgrade to an LS6-Powered Corvette; 5 Reasons to Stay LT2
Michael S. Palmer
