CorvetteForum - Chevrolet Corvette Forum Discussion
Well greased yoke slides new bushing in to keep it aligned
Well greased yoke slides new bushing in to keep it aligned
0 2016/02/20 04:39:28
Old bushing with 1 1/2 pvc pipe to keep it tight to seat the new bushing as its is far in the housing
Old bushing with 1 1/2 pvc pipe to keep it tight to seat the new bushing as its is far in the housing
0 2016/02/20 04:40:42
Seated
Seated
0 2016/02/20 04:42:46
0 2016/02/24 10:40:53
0 2016/02/24 10:41:57
0 2016/02/24 10:42:35
How to remove this. The AIM is lackng
How to remove this. The AIM is lackng
0 2016/02/27 16:45:21
First, remove the inner door panels so you can see the inner mechanism
First, remove the inner door panels so you can see the inner mechanism
0 2016/02/27 16:46:33
Remove the clips from these rods so you can move them out of the way
Remove the clips from these rods so you can move them out of the way
0 2016/02/27 16:47:43
Move the rods
Move the rods
0 2016/02/27 16:49:01
Remove the 3 screws holding the latch mechanism. Its easier to move this now so you can get your hands in the door
Remove the 3 screws holding the latch mechanism. Its easier to move this now so you can get your hands in the door
0 2016/02/27 16:49:49
Drop the mechanism into the door. Be careful of hitting the glass
Drop the mechanism into the door. Be careful of hitting the glass
0 2016/02/27 16:51:04
Remove the nut holding the outside handle in.
Remove the nut holding the outside handle in.
0 2016/02/27 16:52:18
If it doesnt pull out easily push the handle in and look to see if the pivot rod has walked out. Mine did, use needle nose pliers to slide the rod into the hinge
If it doesnt pull out easily push the handle in and look to see if the pivot rod has walked out. Mine did, use needle nose pliers to slide the rod into the hinge
0 2016/02/27 16:53:22
It should pull out easy after that. Then take off the 2 nuts
It should pull out easy after that. Then take off the 2 nuts
0 2016/02/27 16:55:42
0 2016/02/27 16:56:22
Pry the bezel off. It should pop off easily
Pry the bezel off. It should pop off easily
0 2016/02/27 16:57:01
0 2016/02/27 16:58:13
Now push in the button with your thumb and rotate it downward. Hold the top and dont let go once it gets into the door. There should be shims on top of the assembly.
Now push in the button with your thumb and rotate it downward. Hold the top and dont let go once it gets into the door. There should be shims on top of the assembly.
0 2016/02/27 16:59:16
You can see the stack on top of the assembly
You can see the stack on top of the assembly
0 2016/02/27 17:01:12
0 2016/02/27 17:02:00
It will drop into the door and out the openning. Then remove the clip on the rod.
It will drop into the door and out the openning. Then remove the clip on the rod.
0 2016/02/27 17:02:19
Clean it then reove the clip ring on the back
Clean it then reove the clip ring on the back
0 2016/02/27 17:03:31
Using flathead screwdrivers in the sqare slots, pry the ring inward but keep your hand on it, its under spring pressure
Using flathead screwdrivers in the sqare slots, pry the ring inward but keep your hand on it, its under spring pressure
0 2016/02/27 17:04:37
0 2016/02/27 17:06:53
Its all apart and ready to take to the locksmith to be rekeyed.
Its all apart and ready to take to the locksmith to be rekeyed.
0 2016/02/27 17:07:07
0 2016/02/29 06:19:15
0 2016/02/29 06:20:07
0 2016/02/29 06:22:20
0 2016/02/29 06:23:20
0 2016/02/29 06:25:50
Seeping through
Seeping through
0 2016/03/04 09:18:11
0 2016/03/04 09:18:47
0 2016/03/04 09:19:06
Mats are 100.00 alone
Mats are 100.00 alone
0 2016/03/04 09:19:18
New carpets
New carpets
0 2016/03/04 09:20:12
Bubba wiring
Bubba wiring
0 2016/03/05 15:08:54
0 2016/03/05 15:13:33
0 2016/03/05 15:19:03
Non BUBBA No!!!! .......bad bubba
Non BUBBA No!!!! .......bad bubba
0 2016/03/05 15:19:51