CorvetteForum - Chevrolet Corvette Forum Discussion
Click on the yellow postcard
Click on the yellow postcard
0 2016/03/19 18:22:49
His page
His page
0 2016/03/19 18:31:05
0 2016/03/20 05:01:50
From this ......
From this ......
0 2016/03/20 05:37:20
0 2016/03/20 05:37:55
From this....
From this....
0 2016/03/20 05:40:09
To this. It looks so much nicer. It plastic but its cheap.
To this. It looks so much nicer. It plastic but its cheap.
0 2016/03/20 05:40:54
Without....ugly
Without....ugly
0 2016/03/20 05:42:20
Almost looks factory
Almost looks factory
0 2016/03/20 05:43:14
0 2016/03/20 16:26:03
0 2016/03/20 16:27:19
Broken donor
Broken donor
0 2016/03/20 17:08:56
Use the wiper cover as a guide to get it straight
Use the wiper cover as a guide to get it straight
0 2016/03/20 17:10:47
Dremel straight across. Dont cut all the way thru or you'll cut the cover
Dremel straight across. Dont cut all the way thru or you'll cut the cover
0 2016/03/20 17:12:27
I used a small piece of wood and 2 vise grips to keep it straight while I dremeled the opposite side
I used a small piece of wood and 2 vise grips to keep it straight while I dremeled the opposite side
0 2016/03/20 17:14:39
Long enough to get a good bite
Long enough to get a good bite
0 2016/03/20 17:17:54
Scribe a line to fold.it on
Scribe a line to fold.it on
0 2016/03/20 17:20:01
Hammer it over and pound it flat
Hammer it over and pound it flat
0 2016/03/20 17:21:28
0 2016/03/20 17:22:57
Cut off the big piece and put it in the vice to pound it flat
Cut off the big piece and put it in the vice to pound it flat
0 2016/03/20 17:24:51
0 2016/03/20 17:27:35
0 2016/03/20 17:28:30
Nice tight fit, already doesn't move
Nice tight fit, already doesn't move
0 2016/03/20 17:29:10
Clamp everthing together leaving room to jb weld it without gluing the clamps to it
Clamp everthing together leaving room to jb weld it without gluing the clamps to it
0 2016/03/20 17:31:12
Clamping with wood to give more room for the heavy coat. I used alot to fill in the spaces. Make sure not to get it on the surfaces the door will touch
Clamping with wood to give more room for the heavy coat. I used alot to fill in the spaces. Make sure not to get it on the surfaces the door will touch
0 2016/03/20 17:34:12
Cut off the excess on the inside. Use the side of the cut off blade to clean up the visible surface. Then paint
Cut off the excess on the inside. Use the side of the cut off blade to clean up the visible surface. Then paint
0 2016/03/20 17:37:12
Paint it to your desired color. Use a razor blade scraper to slice off the paint on your chrome
Paint it to your desired color. Use a razor blade scraper to slice off the paint on your chrome
0 2016/03/20 17:40:29
0 2016/03/20 17:42:54
0 2016/03/20 17:43:36
0 2016/03/22 05:29:26
0 2016/03/22 06:02:22
0 2016/03/22 06:02:55
0 2016/03/24 19:59:28
0 2016/03/27 18:31:53
0 2016/03/28 05:17:01
Basic c3 vacuum
Basic c3 vacuum
0 2016/03/28 06:43:08
Found this on the net
Found this on the net
0 2016/03/28 06:44:31
Willcox
Willcox
0 2016/03/28 07:11:21
0 2016/04/04 06:32:10
0 2016/04/06 10:58:12