CorvetteForum - Chevrolet Corvette Forum Discussion
Appears to be two receptacles on other end.
Appears to be two receptacles on other end.
0 2026/06/01 05:11:53
Two contacts on the end
Two contacts on the end
0 2026/06/01 05:11:20
Approximately 1-1/16" long x 3/16" thick x 1/2" wide.
Approximately 1-1/16" long x 3/16" thick x 1/2" wide.
0 2026/06/01 05:06:58
Bicycle tube cut to fit the terminal with a hole for the battery post. Additional protection.
Bicycle tube cut to fit the terminal with a hole for the battery post. Additional protection.
0 2026/05/31 04:48:55
Solder on terminal. The best way IMHO
Solder on terminal. The best way IMHO
0 2026/05/31 04:48:13
This is after the 302, with a mild 350, narrowed 12 bolt, DNE 5 spd. Still ran 13 or less thru 1/4. Muddy day at Tri-State.
This is after the 302, with a mild 350, narrowed 12 bolt, DNE 5 spd. Still ran 13 or less thru 1/4. Muddy day at Tri-State.
0 2026/05/30 08:34:14
I was wondering if the pushrods are too short and the rocker is hitting the retainer, but then again, that would be constant.
I was wondering if the pushrods are too short and the rocker is hitting the retainer, but then again, that would be constant.
0 2026/05/21 18:49:50
#2 cylinder - intake valve
#2 cylinder - intake valve
0 2026/05/21 18:45:40
It appears the builder opened up the guide plate for #2 intake.
It appears the builder opened up the guide plate for #2 intake.
0 2026/05/21 18:45:13
#2 cylinder
#2 cylinder
0 2026/05/21 18:44:43
Brass pin in switch housing.
Brass pin in switch housing.
0 2026/05/14 10:25:33
066 ignition switch
066 ignition switch
0 2026/05/14 09:46:27
0 2026/05/11 11:51:16
0 2026/05/11 11:46:35
0 2026/05/11 11:45:27
0 2026/05/11 11:45:15
0 2026/05/11 11:45:04
Valve spring, new damper, old damper, & spacer.
Valve spring, new damper, old damper, & spacer.
0 2026/05/03 14:29:39
Spacer under spring appears to have damage from the damper.
Spacer under spring appears to have damage from the damper.
0 2026/05/03 14:29:37
0 2026/05/01 13:35:22
0 2026/04/27 04:45:28
0 2026/04/27 04:45:14
Thought to be original decals on valve covers.
Thought to be original decals on valve covers.
0 2026/04/25 13:18:43
Remote solenoid on positive post of the battery.
Remote solenoid on positive post of the battery.
0 2026/04/18 04:37:16
0 2026/04/03 18:25:52
3721SB
3721SB
0 2026/03/29 04:17:31
Look closely at the green wire where it enters the grommet.
Look closely at the green wire where it enters the grommet.
0 2026/03/24 05:40:05
latch on the lid
latch on the lid
0 2026/03/14 17:57:19
catch on the ring
catch on the ring
0 2026/03/14 17:56:39
Plastic bumper on the seat bottom
Plastic bumper on the seat bottom
0 2026/03/08 17:51:19
Adjustment screw on both sides
Adjustment screw on both sides
0 2026/03/08 17:51:03
Yellowish residue on the intake at thermostat housing. ????
Yellowish residue on the intake at thermostat housing. ????
0 2026/03/04 07:46:27
Yellowish residue on the intake - fuel???
Yellowish residue on the intake - fuel???
0 2026/03/04 07:46:03
Homemade tool to check caster.
Homemade tool to check caster.
0 2026/03/04 07:18:28
Plumb bob down from ends of horizontal bar to make marks for setting toe-in. Camber gauge or even a level to set camber and caster.
Plumb bob down from ends of horizontal bar to make marks for setting toe-in. Camber gauge or even a level to set camber and caster.
0 2026/03/04 07:18:03
5/8" hose fitting. has internal baffle. A grommet would be needed to fit in the hole a the back of the block.
5/8" hose fitting. has internal baffle. A grommet would be needed to fit in the hole a the back of the block.
0 2026/02/26 14:08:03
0 2026/02/26 13:50:39
Original 3367 Holley with air cleaner base and fresh air tube shot.
Original 3367 Holley with air cleaner base and fresh air tube shot.
0 2026/02/25 09:58:42
Fresh air tube to engine block
Fresh air tube to engine block
0 2026/02/25 09:58:12
Air cleaner base with fresh air tube and 1" rubber hose..
Air cleaner base with fresh air tube and 1" rubber hose..
0 2026/02/25 09:57:33