CorvetteForum - Chevrolet Corvette Forum Discussion
0 2021/02/10 11:19:10
Turning the green knob allows one part of the brass connector to come apart. You only need one per car.
Turning the green knob allows one part of the brass connector to come apart. You only need one per car.
0 2021/02/01 16:27:41
0 2021/01/28 07:01:49
0 2021/01/28 07:01:43
0 2021/01/28 07:01:30
0 2021/01/28 07:01:22
0 2021/01/28 07:01:14
0 2021/01/18 20:55:02
0 2021/01/18 20:54:51
0 2021/01/18 20:54:35
0 2021/01/18 20:54:21
Plug to tranny switch left of brake mater cylinder
Plug to tranny switch left of brake mater cylinder
0 2021/01/18 20:54:06
0 2021/01/18 20:53:57
0 2021/01/18 20:53:48
The cut out section goes around the chrome receiver on the rear deck lid. Inside against painted rear deck, remove plate after threaded shafts are in receivers.
The cut out section goes around the chrome receiver on the rear deck lid. Inside against painted rear deck, remove plate after threaded shafts are in receivers.
0 2021/01/17 08:27:16
The brown stuff is “leaking” on the front and back side of the metal spoke
The brown stuff is “leaking” on the front and back side of the metal spoke
0 2020/11/24 06:04:53
0 2020/11/24 06:04:48
Brown looking stuff where metal spoke meets black vinyl/rubber
Brown looking stuff where metal spoke meets black vinyl/rubber
0 2020/11/24 06:04:43
0 2020/11/16 06:33:18
The part in the plastic bag on your photo maybe the tilt wheel spring, but not sure why you would have two?
The part in the plastic bag on your photo maybe the tilt wheel spring, but not sure why you would have two?
0 2020/11/12 06:32:40
If the three screws are not orientated like above the Horn Button will not go on correctly
If the three screws are not orientated like above the Horn Button will not go on correctly
0 2020/11/10 15:27:18
Here is a phot with
Here is a phot with
0 2020/11/10 15:27:01
0 2020/11/10 15:26:48
This correct so that the horn button will go on straight
This correct so that the horn button will go on straight
0 2020/11/10 15:26:29
0 2020/10/25 07:02:25
0 2020/10/25 07:02:17
0 2020/10/25 07:02:10
The nail will Make a perfect depression in the center of the rivet.
The nail will Make a perfect depression in the center of the rivet.
0 2020/10/25 06:51:18
Your page number may be different as this is a 1973 Service Manual.
Your page number may be different as this is a 1973 Service Manual.
0 2020/10/16 17:13:43
Ensure that your 72 Fuse Box is the same as my 72
Ensure that your 72 Fuse Box is the same as my 72
0 2020/10/16 13:31:21
The left side of the tool is 1/2 inch wide, and the metal thickness is approx 2 credit cards. My screwdrivers, were too thick.
The left side of the tool is 1/2 inch wide, and the metal thickness is approx 2 credit cards. My screwdrivers, were too thick.
0 2020/10/14 07:51:41
You may have a different model, if so give Edelbrock a call
You may have a different model, if so give Edelbrock a call
0 2020/10/14 07:11:48
Willcox states they a picture on the wall for their techs to use when doing the replacement, look at the wiring order closely
Willcox states they a picture on the wall for their techs to use when doing the replacement, look at the wiring order closely
0 2020/10/11 08:37:34
0 2020/10/11 08:37:28
OEM
OEM
0 2020/10/11 08:37:21
0 2020/10/11 08:30:08
0 2020/10/11 08:30:03
0 2020/10/11 08:29:56
0 2020/10/11 08:29:49
0 2020/10/11 08:29:42