Kenwood DNX7100
#21
Drifting
There are three connections on the Kenwood, pretty fool proof...
1. USB - This is for any device, but on the iPod it communicates the track/song info and iPod control
2. Audio - standard pin plug (like headphones) - the ip200 / 300 have this audio pin to plug into that.
3. Video - the IP300 has this additional pin on it for 5gen iPod video
All that being said, I had mine plugged into the video by accident, but that took all of 30 seconds to figure out, he stated that he is getting video so I have to assume that he plugged in the audio into the correct port.
Yes, it is possible (since you tried two cables) that the Kenwoods ipod audio cable is bad.
This may or may not work, can you try a dual pinned headphone style cord from radio shack or something to test the audio from the headphone output of the ipod (or anything else), the only other alternative is to switch out the HU. Like others have said, I do not believe there is any configuration, I have been through most menus and have not seen this as an option.
Good luck on this...
1. USB - This is for any device, but on the iPod it communicates the track/song info and iPod control
2. Audio - standard pin plug (like headphones) - the ip200 / 300 have this audio pin to plug into that.
3. Video - the IP300 has this additional pin on it for 5gen iPod video
All that being said, I had mine plugged into the video by accident, but that took all of 30 seconds to figure out, he stated that he is getting video so I have to assume that he plugged in the audio into the correct port.
Yes, it is possible (since you tried two cables) that the Kenwoods ipod audio cable is bad.
This may or may not work, can you try a dual pinned headphone style cord from radio shack or something to test the audio from the headphone output of the ipod (or anything else), the only other alternative is to switch out the HU. Like others have said, I do not believe there is any configuration, I have been through most menus and have not seen this as an option.
Good luck on this...
#22
Yes, you are correct - audio, video, and usb - they are all plugged in correctly. My issue is bigger than the iPod as I found out today, I have found that the DVD sound is not working either. Actually what I have discovered is that if I just connect a speaker directly to the RCA's or regular speaker wires on the HU, I get sound for everything - iPod, DVD, Tuner (louder than the rest), etc. But when I connect them to the wires on the GMCO, I only get sound on the tuner. What could be different about the sound from the Tuner vs. all other sources that it works through the car speakers and the rest do not? Is it something with the Bose system? Any suggestions?
#23
Le Mans Master
your stock amp isnt turning on unless you are on tuner, basically u connected the power antenna wire instead of the amp turn on wire
so go behind the dash and find where you hooked the power antenna wire from the kenwood to the gmco and unhook that and use the amp turn on wire instead and you will be set
so go behind the dash and find where you hooked the power antenna wire from the kenwood to the gmco and unhook that and use the amp turn on wire instead and you will be set
#25
Le Mans Master
uhhhhhhh, try the rca's if its not getting loud enough go to the speaker wires
if i recall on a bose car you deff use rca's and on the non-bose I dont remeber
if i recall on a bose car you deff use rca's and on the non-bose I dont remeber
#26
Drifting
your stock amp isnt turning on unless you are on tuner, basically u connected the power antenna wire instead of the amp turn on wire
so go behind the dash and find where you hooked the power antenna wire from the kenwood to the gmco and unhook that and use the amp turn on wire instead and you will be set
so go behind the dash and find where you hooked the power antenna wire from the kenwood to the gmco and unhook that and use the amp turn on wire instead and you will be set
#29
Instructor
Member Since: May 2001
Location: Aurora Co
Posts: 240
Likes: 0
Received 0 Likes
on
0 Posts
Quick question.
Can this unit be installed in a Bose Car and still work without changing speakers and adding amps?
I want to change out everything but I would like to do it in two phases.
Thanks,
Nelson
Can this unit be installed in a Bose Car and still work without changing speakers and adding amps?
I want to change out everything but I would like to do it in two phases.
Thanks,
Nelson
#30
Le Mans Master
Member Since: Oct 2006
Location: Bradenton, FL & Chandler AZ
Posts: 5,474
Likes: 0
Received 3 Likes
on
3 Posts
St. Jude Donor '09
I have been considering the same unit (Kenwood DNX7100). A local shop quoted $1,300 for the unit and $315.00 for install. Are these fair prices? I know I can get the unit cheaper through some internet electronic shops, but those are usually not manufacturer approved vendors and I'm afraid about warranty issues. Where did you guys purchase yours and was the above an issue?
Thanks
Thanks
#32
Le Mans Master
you should be able to use stock sat radio antenna
on a C6 you can keep bose and add this unit, its a great piece
Ive always bought from sonicelectronix and never a problem yet
on a C6 you can keep bose and add this unit, its a great piece
Ive always bought from sonicelectronix and never a problem yet
#33
Yes, I just did it in an 07 coupe with Bose / no OnStar (finished it yesterday) - with 7100, bluetooth, camera, video ipod. It all worked really well today...I will keep everyone updated. Also I documented the entire install, alot of good pics if you need any examples.
#34
#35
http://www.abesofmaine.com/item.do?item=KWDNX7100
I know these guys are good to work with and have a great price as well. I personally purchased locally and they matched Crutchfield prices, could have save about $300 over the internet but I installed it myself so...
I know these guys are good to work with and have a great price as well. I personally purchased locally and they matched Crutchfield prices, could have save about $300 over the internet but I installed it myself so...
#36
Burning Brakes
Member Since: May 2006
Location: Evergreen colorado
Posts: 876
Likes: 0
Received 0 Likes
on
0 Posts
Going to start install of 7100 tomorrow that is the only thing that hasn't changed. Still working on the final amp,speaker setup. Work much better under pressure.....
Jarad
Jarad
#37
Racer
Yes, I just did it in an 07 coupe with Bose / no OnStar (finished it yesterday) - with 7100, bluetooth, camera, video ipod. It all worked really well today...I will keep everyone updated. Also I documented the entire install, alot of good pics if you need any examples.
#38
Started install today on 2005 with bose and Onstar using gmah24b and according to peripheral's website we do not need the chime module(gmahcm). jhowever i have no chimes. does anyone have any input that could help, will be trying to complete install sunday the 1st.
#39
Successful Plumber
Member Since: Feb 2001
Location: Top of the hill, 3rd mailbox on the right. Texas
Posts: 43,830
Likes: 0
Received 13 Likes
on
6 Posts
CF NCM Ambassador
CI 6-7-9-10 Veteran
St. Jude Donor '06-'07-'08-'09-'10
NCM Member '09
Yes, I just did it in an 07 coupe with Bose / no OnStar (finished it yesterday) - with 7100, bluetooth, camera, video ipod. It all worked really well today...I will keep everyone updated. Also I documented the entire install, alot of good pics if you need any examples.