E Brake handle, light switch ??
Thread Starter
Team Owner
Joined: May 2002
Posts: 24,459
Likes: 13
From: Phoenix
St. Jude Donor '03-'04-'05-'09
E Brake handle, light switch ??
Have my E Brake light staying on, when the e brake is not on. Looking at the switch, it sits about an inch from a metal tab sticking out from the E brake handle assembly, that would depress it when released.
Had to be something slide on the tab part, to be able to reach the switch and fill the inch gap?
I've looked and cannot find anything related for a diagram of this area to see what's needed.
Any help? Any knowledge of a part I'm missing?
It didn't do this before, and I cannot locate anything that may of fell into the console area.
Had to be something slide on the tab part, to be able to reach the switch and fill the inch gap?
I've looked and cannot find anything related for a diagram of this area to see what's needed.
Any help? Any knowledge of a part I'm missing?
It didn't do this before, and I cannot locate anything that may of fell into the console area.
Le Mans Master
Joined: Jul 2006
Posts: 8,117
Likes: 104
From: charlotte north carolina
the switch completes the circuit to ground when the metal tabs on the slide contact the small bracket that it moves through. there's a spring that's supposed to push the slide when the brake handle is released. if the slide is moving properly, check for a short.
Team Owner
Joined: Jun 2000
Posts: 38,923
Likes: 1,482
From: Southbound
Cruise-In II Veteran
You can adjust the switch to close against the tab on the ebrake handle. UPC 12 Sheet B9 in the AIM shows the installation.
Last edited by Easy Mike; Jan 27, 2013 at 09:14 AM.
Thread Starter
Team Owner
Joined: May 2002
Posts: 24,459
Likes: 13
From: Phoenix
St. Jude Donor '03-'04-'05-'09
Have the manual, don't see a switch adjustment, or any part that would fit on the tab, but will look a little closer.
I see two holes for the switch mount, but assumed one was for the bolt, the other for a indent/ recessed part, so the switch mount won't swivel
Thanks
I see two holes for the switch mount, but assumed one was for the bolt, the other for a indent/ recessed part, so the switch mount won't swivel
Thanks
Thread Starter
Team Owner
Joined: May 2002
Posts: 24,459
Likes: 13
From: Phoenix
St. Jude Donor '03-'04-'05-'09
It's as I described in previous post. So there must be adjustment of the e-brake handle? Actually the tab part is about 1/4" from making contact with the switch. And I see there may be about 3 teeth, where the e-brake handle could go further down...I guess.
Thread Starter
Team Owner
Joined: May 2002
Posts: 24,459
Likes: 13
From: Phoenix
St. Jude Donor '03-'04-'05-'09
I can see this as an adjustment issue. Having a few teeth on the ratchet left...but the handle is already low to the console, anymore and I'll have to notch it out to be able to get a finger under the handle 
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
5 Best & 5 Worst Corvette Daily Drivers
Joe Kucinski
The Headlights of Every Corvette Generation Explained
Joe Kucinski
5 Best & 5 Most Overrated Corvette Track Packages of All Time!
Joe Kucinski
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
