1st Time using Timing light need quick answer.
Thread Starter
Instructor
Joined: Dec 2004
Posts: 230
Likes: 6
From: Washington DC
1st Time using Timing light need quick answer.
Got a new timing light and I want to check timing.
Connect the Inductive Clip to the #1 wire. OK
Connect the Black Clip to the engine block. OK
Connect the Red Clip to the Positive Battery Terminal. NOT OK
Battery is behind the drivers seat.
Where should I attach the Red Clip????
Is a Corvette a 12V Positive ground system????
Quick help.
Thanks
Connect the Inductive Clip to the #1 wire. OK
Connect the Black Clip to the engine block. OK
Connect the Red Clip to the Positive Battery Terminal. NOT OK
Battery is behind the drivers seat.
Where should I attach the Red Clip????
Is a Corvette a 12V Positive ground system????
Quick help.
Thanks
Last edited by Al77Vette; Jul 24, 2006 at 08:39 PM.
Race Director
Joined: Feb 1999
Posts: 19,659
Likes: 34
From: Lenoir City Tennessee
Ci 6, 8 & 10 Veteran
St. Jude Donor '05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15
My timing light connections. Just be sure when you connect to the positive, do not accidently let the clip come into contact with the alternator case at the same time.
BTW, I have reclocked my alternator so my connections will be in a different place than yours. Just be sure to get on ground connection and positive on the alternator.
Thread Starter
Instructor
Joined: Dec 2004
Posts: 230
Likes: 6
From: Washington DC
Timing is OK.. 10 degrees @ 800 rpms.
I had some bubba work on the car this week and he left a rag in the intake manifold. So when I started the car, (Oh I mean bubba) it sucked the rag in to cylinder #8. He had to take the intake and rockers off to get it out. To make a long story short cleaned the intake while it was off and wipe off the timing reference marks. It’s been a long weekend.
I had some bubba work on the car this week and he left a rag in the intake manifold. So when I started the car, (Oh I mean bubba) it sucked the rag in to cylinder #8. He had to take the intake and rockers off to get it out. To make a long story short cleaned the intake while it was off and wipe off the timing reference marks. It’s been a long weekend.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Thread Starter
Instructor
Joined: Dec 2004
Posts: 230
Likes: 6
From: Washington DC
[QUOTE=Eddie 70My timing light connections. Just be sure when you connect to the positive, do not accidently let the clip come into contact with the alternator case at the same time.
[/QUOTE]
I did that once, and had to replace the starter wiring harnes. I am leaning the hard way.
[/QUOTE]
I did that once, and had to replace the starter wiring harnes. I am leaning the hard way.
