Trailing Arm removal
Thread Starter
Le Mans Master
Joined: Jun 1999
Posts: 5,548
Likes: 41
From: Conn.
St. Jude Donor '21
Trailing Arm removal
Thinking of sending my arms out to Bairs for rebuilds. For some reason seeing the SNOW fly again seems to take me out of that mode. Maybe in the next couple of weeks I'll get started. Any info regarding the removal of these arms will be greatly appreciated, ideas, shortcuts etc. Already purchased a can of PB Blaster! :banghead: :flag
Drifting
Joined: Jan 2002
Posts: 1,645
Likes: 11
From: Schaumburg IL
Re: Trailing Arm removal (SEE3ER)
Log on to the Van Steel website and order their VHS tape on Vette Suspensions. It is about $20 and worth many times that in knowledge of the rear end disassembly and assembly.
http://www.vansteel.com
or call Art at 727-561-9199, he is a super help.
http://www.vansteel.com
or call Art at 727-561-9199, he is a super help.
Le Mans Master
Joined: Dec 2001
Posts: 7,788
Likes: 6
From: Winchester TN
Cruise-In III Veteran
Cruise-In IV Veteran
Cruise-In V Veteran
St. Jude Donor '03-'04-'05-'06-'07-'11
Re: Trailing Arm removal (SEE3ER)
Hi SEE3ER -
We had to resort to a sawzall - PITA.
Here is a picture of the promised land for you -
good luck and
best regards -
mqqn
We had to resort to a sawzall - PITA.
Here is a picture of the promised land for you -
good luck and
best regards -
mqqn
Tech Contributor
Joined: Aug 1999
Posts: 15,173
Likes: 3,982
From: Connecticut, USA
Re: Trailing Arm removal (SEE3ER)
Steve if you're down in New Haven let me know. I have a couple of arms out that I rebuilt, you could take a look at. It might help you get a feel for removing them.
Gary
Gary
Tech Contributor
Joined: Aug 1999
Posts: 15,173
Likes: 3,982
From: Connecticut, USA
Re: Trailing Arm removal (SEE3ER)
Well I only work on things as time allows-usually nights and weekends. Were you thinking of doing these yourself? How fast do you need them back?
IM me if you have questions.
Gary
IM me if you have questions.
Gary
Le Mans Master
Joined: Jun 2002
Posts: 8,339
Likes: 24
From: I can walk to MA
Re: Trailing Arm removal (SEE3ER)
You better get your butt moving on that. I know -I'm watching the snow fall in MA as I write this - but ...
You WILL run into problems. You WILL take longer than expected. You WILL
replace thiongs you hadn't planned to. Best to get it rolling, so your not
still fixing her in August.
IMO - it's cheap insurance to pay a pro to do the TA rebuild - at least the bearing assembly. It's not that much more to pay for the whole matched
assembly to be rebuilt. ~$3-400 each depending on brake hardware.
:seeya
[Modified by NHvette, 11:47 AM 4/9/2003]
You WILL run into problems. You WILL take longer than expected. You WILL
replace thiongs you hadn't planned to. Best to get it rolling, so your not
still fixing her in August.
IMO - it's cheap insurance to pay a pro to do the TA rebuild - at least the bearing assembly. It's not that much more to pay for the whole matched
assembly to be rebuilt. ~$3-400 each depending on brake hardware.
:seeya
[Modified by NHvette, 11:47 AM 4/9/2003]
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Racer
Joined: Sep 2000
Posts: 267
Likes: 0
From: Austin TX
Re: Trailing Arm removal (SEE3ER)
I rebuilt mine last fall. I'll admit it was a PITA but i really didn't think it was worth the 350 that Van Steel (or whoever) was charging. I've done harder things on the car, it just took time and patience.
Getting them out wasn't too bad. Definitely lots of penetrating oil, but mine slit out without too much effort. Replaced everything (poly bushings and stainless hardware).
It’d do it again if the option were to arise.
Oh yeah… check the run out BEFORE you install the grease. :P
-thomas
Getting them out wasn't too bad. Definitely lots of penetrating oil, but mine slit out without too much effort. Replaced everything (poly bushings and stainless hardware).
It’d do it again if the option were to arise.
Oh yeah… check the run out BEFORE you install the grease. :P
-thomas
Pro
Joined: Mar 2003
Posts: 553
Likes: 1
From: Valparaiso IN
Re: Trailing Arm removal (mqqn)
WOW.. That IS the promised land!! Mine are at Bair's as we speak. I have rusty pockets where the old TAs were. Did you use POR 15 on that? What is my next move to get mine looking like that? :eek: :smash:
