3D models
#1
Advanced
Thread Starter
3D models
Hello from Finland
First time to write in here...
Doesn't know is this correct place for this my question...
So, my project is LS swap to -84 C4 (LQ9 with LS3 heads + 4L65E etc.)
My problem is that I work a lot with Autodesk Inventor and of course I would like to make nice plan, all needed parts (engine/transmission supports, accessory supports...) ready before I get new engine or take old away.
And for that I have tried to found 3D models for components.
Engine model I already have (LS3), but haven't found transmission or any other C5 Corvette.. Chevy parts what going to use.
(files should be .step, iges etc)
Does anybody knows, can those be found somewhere?
For engine room, transmission tunnel... I will make 3D scanning, so it would be nice to do everything ready on screen.. then doesn't have any big problems what you don't know or already clarified those problems...
And when it's done, I think, no problem to share models to other users here
- Vesa
First time to write in here...
Doesn't know is this correct place for this my question...
So, my project is LS swap to -84 C4 (LQ9 with LS3 heads + 4L65E etc.)
My problem is that I work a lot with Autodesk Inventor and of course I would like to make nice plan, all needed parts (engine/transmission supports, accessory supports...) ready before I get new engine or take old away.
And for that I have tried to found 3D models for components.
Engine model I already have (LS3), but haven't found transmission or any other C5 Corvette.. Chevy parts what going to use.
(files should be .step, iges etc)
Does anybody knows, can those be found somewhere?
For engine room, transmission tunnel... I will make 3D scanning, so it would be nice to do everything ready on screen.. then doesn't have any big problems what you don't know or already clarified those problems...
And when it's done, I think, no problem to share models to other users here
- Vesa
#5
Advanced
Thread Starter
That's not what I'm looking, I try to found 3D models, so that I can install everything on screen, model all brackets etc, so can manufacture needed parts ready before even have new engine/transmission...
Engine I did found... nothing else
3D model from LS3
Engine I did found... nothing else
3D model from LS3
#6
Drifting
There would be no original 3D models that would work in your system from a C4. Even in 96, true 3D modeling was very rarely used. in 84, you would have had wire frame 3D designs. Unless someone is scanning and converting old parts, this is probably a unicorn hunt.
#7
Advanced
Thread Starter
And now I'm asking models for LS3 + 4L65E + LS3 Corvette parts, those are not so old. And as did write, I'm going to make scanning for car
#8
Melting Slicks
You're lucky you have the engine model. I've never seen a 3D model of a C4 engine bay yet and I have been looking for a long time. Turbosquid has C4 models but the engines are not detailed ... also you would have to do some sort of shape-capture from the 3D files to import into Inventor.
https://www.turbosquid.com/3d-models...e-sport/599783
https://www.turbosquid.com/3d-models...e-sport/599783
The following users liked this post:
3D-Aircrew (02-05-2019)
#13
Melting Slicks
#14
Advanced
Thread Starter
Yes, from grabcad I did found that LS3 model, but no luck with transmissions
4L65E is coming, so should like to get model for that and for TH700r4.
And models should be quite accurate, to see how there is free space on tunnel and how support will fit...
4L65E is coming, so should like to get model for that and for TH700r4.
And models should be quite accurate, to see how there is free space on tunnel and how support will fit...