Anyone Tried These Headers?
#1
Guest
Posts: n/a
Anyone Tried These Headers?
Hey guys. I've lurked here for a while and finally registered. You guys really know your stuff! I finally know where to go for good info. I'm the only guy I know with a Corvette! Everyone I know runs older stuff. When I beat 'em they cry.
Anyway, anyone know anything about the Vanderzangen (I think that's the name!) headers? Check 'em out on http://www.vetteexhaust.com. The price is right, but I think I'll save up for the Hooker Super Comps unless someone can recommend them. Also, I don't think they have provisions for emissions.
Anyway, anyone know anything about the Vanderzangen (I think that's the name!) headers? Check 'em out on http://www.vetteexhaust.com. The price is right, but I think I'll save up for the Hooker Super Comps unless someone can recommend them. Also, I don't think they have provisions for emissions.
#2
Team Owner
stay away from him!!!
He has a really bad reputation on this board. He burned a member Fastguy for a few hundred and the system he sent him completely didn't not fit the car. Look at his ebay feedback, you'll see.
He has a really bad reputation on this board. He burned a member Fastguy for a few hundred and the system he sent him completely didn't not fit the car. Look at his ebay feedback, you'll see.
#4
Safety Car
Re: (scorp508)
I have not heard of this guy but if he has screwed someone over then I would certainly steer clear
#5
Team Owner
I have not heard of this guy but if he has screwed someone over then I would certainly steer clear
#8
Re: Anyone Tried These Headers? (Jim-K)
I don't remember all the details, but I do remember reading the thread. Pretty ugly! Don't do it!!! :nonod:
BTW - Welcome to another MN Vette owner!! I'm just a little north and east of you in Ham Lake.
BTW - Welcome to another MN Vette owner!! I'm just a little north and east of you in Ham Lake.
#10
Burning Brakes
Re: Anyone Tried These Headers? (topjimmy87)
I would recommend the TPiS headers. I have them and they install easily even for a relative novice like me. I did it with the car on jackstands in my garage. Plus, you are close to them. Their garage is in Chaska. They are very helpful and they know their stuff. It's worth the extra money to avoid the headaches.
Greg
Esko, MN :D
Greg
Esko, MN :D
#11
Le Mans Master
Re: Anyone Tried These Headers? (topjimmy87)
Wow, I just checked out the webpage...that stuff looks like total junk!! I would hate to try and make that crap fit on a car...
#12
Le Mans Master
Re: Anyone Tried These Headers? (topjimmy87)
Ha Ha. The Corvette Forum is not on thier Vette Links page. That right there should tell you to stay away from them.
:smash: :smash: :smash: :smash: :smash: :smash:
:smash: :smash: :smash: :smash: :smash: :smash:
#14
Safety Car
Re: Anyone Tried These Headers? (Sharky Guam)
You most often get what you pay for. You might check out JBA's, a little expensive but darn good headers. Go in fairly easily and ,BTW, get them ceramic coated for less heat problems.
[Modified by ittlfly, 5:06 PM 6/20/2002]
#15
Le Mans Master
Re: Anyone Tried These Headers? (topjimmy87)
What ever you buy, buy them uncoated and have them shipped directly to Jet Hot.
I have a set from TPIS that came coated. Tomorrow they are going to Jet Hot to be recoated right. Jet Hot is doind a group purchase right now for 30% off.
I had a set on my Z28 that were Jet Hot coated. They looked great for years and still looked great when I sold the car.
I have a set from TPIS that came coated. Tomorrow they are going to Jet Hot to be recoated right. Jet Hot is doind a group purchase right now for 30% off.
I had a set on my Z28 that were Jet Hot coated. They looked great for years and still looked great when I sold the car.
#16
Team Owner
Re: Anyone Tried These Headers? (ZBRA)
OK, go grab a beer and some popcorn and read this.
http://forums.corvetteforum.com/zerothread?id=261915
I am using the Hooker SC 2149's from Summit, $449. Easy to install, still look good after four months.
http://forums.corvetteforum.com/zerothread?id=261915
I am using the Hooker SC 2149's from Summit, $449. Easy to install, still look good after four months.
#17
Re: Anyone Tried These Headers? (topjimmy87)
All they are are Hedman Hedders...I bought a pair off someone on Ebay. They fit OK, but they're nothing special. Also, there is no pre-tapped O2 bung :smash: