some progress pics...
Thread Starter
Drifting
Joined: May 2003
Posts: 1,979
Likes: 48
From: Lakeport CA
some progress pics...
Here are my 113 heads that I ported & polished exhaust & ourside. Also note the stock polished valve covers. Can be done but I don't want to talk about the hours I put into it... :crazy:
Oh & my new single mass alum flywheel & clutch...
[Modified by Trog, 4:40 PM 11/16/2003]
[Modified by Trog, 4:42 PM 11/16/2003]
[Modified by Trog, 4:42 PM 11/16/2003]
[Modified by Trog, 4:43 PM 11/16/2003]
Oh & my new single mass alum flywheel & clutch...
[Modified by Trog, 4:40 PM 11/16/2003]
[Modified by Trog, 4:42 PM 11/16/2003]
[Modified by Trog, 4:42 PM 11/16/2003]
[Modified by Trog, 4:43 PM 11/16/2003]
Elite Torch Red Member
Joined: Sep 1999
Posts: 57,805
Likes: 23
From: Exit 89 GSP,Lakewood,NJ The Land Of Mojo
Cental/South NJ Events Coordinator
CI 1-2-3-4-5-6-7-8-9-10-11-12 Vet
CI-II Burnout & Drag Champ
St. Jude Donor '03-'04-'05-'06-'07
Re: some progress pics... (Trog)
:thumbs:
Burning Brakes
Joined: Feb 2002
Posts: 825
Likes: 0
From: Pittsburgh PA
Re: some progress pics... (Trog)
trog
those pics look really good. i am going to be sanding down my valve covers to repaint them, what did you use to get inside the fins to clean them out? the previous owner threw on a really thick and sloppy coat of paint and they look horrible especially inside those groves :smash:
those pics look really good. i am going to be sanding down my valve covers to repaint them, what did you use to get inside the fins to clean them out? the previous owner threw on a really thick and sloppy coat of paint and they look horrible especially inside those groves :smash:
Thread Starter
Drifting
Joined: May 2003
Posts: 1,979
Likes: 48
From: Lakeport CA
Re: some progress pics... (MIke350)
Start w/ paint remover, there are like 3 coats in the factory paint on the valve covers (Grey, brown, black). Then I used a fine machinist file to smooth out the casting marks, then worked down from like 220 to 1500 wet dry sand paper. Did that a couple years ago, today I just used a buffing wheel on my grinder w/ some rouge to repolish it out again.
The stock covers appear to be alum. Didn't notice any color like you would find in mag.
The stock covers appear to be alum. Didn't notice any color like you would find in mag.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
