quick question for steering column lock
Thread Starter
Burning Brakes
Joined: Apr 2008
Posts: 1,050
Likes: 1
From: Bartlett IL
quick question for steering column lock
I know there are quite a few threads about this, well here's the good part i ordered a column lock bypass and is suppose to be here Monday, the bad part, it went out on me tonight. I know you once it goes out you can't put the bypass in to fix it, but if I bring it to the stealership would they put it in for me?
I have a feeling it's probably a no, correct? Sorry for such a silly question. and any suggestion for getting the vette on the flatbed when they come and tow it for me?
I have a feeling it's probably a no, correct? Sorry for such a silly question. and any suggestion for getting the vette on the flatbed when they come and tow it for me?
Tech Contributor
Joined: Dec 2003
Posts: 19,384
Likes: 87
From: Horncastle Lincolnshire, England
2023 C5 of the Year Finalist - Unmodified
First thing to try is move the steering wheel back and forth quite hard to see if it will unlock. Sometimes the vibration is enough to drop the locking pin back in place.
From the sticky:
Sometimes the latching relay in the CLB can get out of sync sending the wrong status to your BCM. This has happened to a few folks even with the CLB installed. The CLB latching relay gets out of sync with the BCM possibly due to shock, vibration or relay contact bounce during switching which confused the BCM. The CLB does not physically know which state it should be in; it only switches from one state to the other when it receives a signal from the BCM. The BCM can be reset by pulling Fuse 23 and waiting 10 seconds.
Once its unlocked get that CLB on there pronto
Try to avoid the dealer if at all possible. They'll try to fit the recall kit and charge you a fortune for the shafting.
From the sticky:
Sometimes the latching relay in the CLB can get out of sync sending the wrong status to your BCM. This has happened to a few folks even with the CLB installed. The CLB latching relay gets out of sync with the BCM possibly due to shock, vibration or relay contact bounce during switching which confused the BCM. The CLB does not physically know which state it should be in; it only switches from one state to the other when it receives a signal from the BCM. The BCM can be reset by pulling Fuse 23 and waiting 10 seconds.
Once its unlocked get that CLB on there pronto
Try to avoid the dealer if at all possible. They'll try to fit the recall kit and charge you a fortune for the shafting.
Last edited by DeeGee; Nov 29, 2009 at 03:41 AM.
Drifting
Joined: Feb 2007
Posts: 1,793
Likes: 7
From: Santa Maria Ca.
You may be able to get it unlocked by banging on the steering wheel while inserting the key-there are a few threads on it,do a search.
If you DO get it unlocked,just leave the key in the switch till you install the bypass on Monday-if you don't pull the key,it doesn't lock the column
Good Luck-you had the right idea,it just failed a day or two too soon!!
If you DO get it unlocked,just leave the key in the switch till you install the bypass on Monday-if you don't pull the key,it doesn't lock the column
Good Luck-you had the right idea,it just failed a day or two too soon!!
Administrator
Joined: Mar 2001
Posts: 368,522
Likes: 24,823
From: In a parallel universe. Currently own 2014 Stingray Coupe.
C7 of the Year - Modified Finalist 2021
MO Events Coordinator
St. Jude Co-Organizer
St. Jude Donor '03 thru '26
NCM Sinkhole Donor
CI 5, 8 & 11 Veteran
with the above. Good luck getting it unlocked and with the install.
Thread Starter
Burning Brakes
Joined: Apr 2008
Posts: 1,050
Likes: 1
From: Bartlett IL
Thanks again guys. I will give this a try. So if it's unlocked when I turn the key on, do I have to leave it on or can I turn the key back to off, but leave the key in there?
Thread Starter
Burning Brakes
Joined: Apr 2008
Posts: 1,050
Likes: 1
From: Bartlett IL
Okay thank you! Then when my CLB comes in tomorrow, just leave the key in and put in the CLB and everything should be good? (even when I take the key out after it's installed).
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Thread Starter
Burning Brakes
Joined: Apr 2008
Posts: 1,050
Likes: 1
From: Bartlett IL
Okay I apologize for any confusion, I have been talking with 8Vette7 and he has been a big help to me for clarifying everything up. I do have the solid lock ring installed in my car (I can turn it freely without the key, despite a little effort) but the motor kills. IF I have the fuel shut off program what do I do then to remove this or fix this so it won't kill my fuel? I should be receiving my CLB today. Also I put the key in and turned it to ''on'' position with the engine off, should the ''service steering column lock'' still come up? Or is it only if the engine is running?
Thank you again.
Thank you again.
Thread Starter
Burning Brakes
Joined: Apr 2008
Posts: 1,050
Likes: 1
From: Bartlett IL
Well, I put the CLB in today and everything seems to be working! I took the K-Harness out and no codes or messages or anything come up anymore. Took me about 30 minutes to do (hardest thing was getting the knee bolster off haha) and I would like to thank everyone that helped me with this and sorry for another pesky ''steering column thread'' 
