mrr23 mod thread
Drifting
Joined: Mar 2012
Posts: 1,517
Likes: 147
From: Jasper Alabama
Looking good. The C7 carbon ZR spoiler will go very well with everything you have done so far. Are you going with the carbon fiber? Carbon would look killer with the forest green. Will you add a front splitter as well. Just ordered another carbon fiber C5R front splitter for mine. Snapped the one that was on my car clean in two! Looks naked without it now.
Last edited by Stealth02; Jun 9, 2015 at 11:13 AM.
Thread Starter
Melting Slicks
Joined: Jul 2004
Posts: 3,092
Likes: 120
From: orlando florida
St. Jude Donor '15
Looking good. The C7 carbon ZR spoiler will go very well with everything you have done so far. Are you going with the carbon fiber? Carbon would look killer with the forest green. Will you add a front splitter as well. Just ordered another carbon fiber C5R front splitter for mine. Snapped the one that was on my car clean in two! Looks naked without it now.
Thread Starter
Melting Slicks
Joined: Jul 2004
Posts: 3,092
Likes: 120
From: orlando florida
St. Jude Donor '15
removed my polished race mesh because it didn't match the tigershark mesh and added these from corvettemods.
when the car was painted, i removed the acrylic rear bumper lettering . i know have these domed silver letters i bought through north american tuning only to find out they drop shipped from vette works international in tampa florida.
for giggles, i put the front corvette emblem in the mesh on the tigershark bumper.
when the car was painted, i removed the acrylic rear bumper lettering . i know have these domed silver letters i bought through north american tuning only to find out they drop shipped from vette works international in tampa florida.
for giggles, i put the front corvette emblem in the mesh on the tigershark bumper.
Thread Starter
Melting Slicks
Joined: Jul 2004
Posts: 3,092
Likes: 120
From: orlando florida
St. Jude Donor '15
had them done at sikwhips customs here in orlando.
http://tredalign.com/vette/exterior/frccarbon.mp4
http://tredalign.com/vette/exterior/frccarbon.mp4
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Thread Starter
Melting Slicks
Joined: Jul 2004
Posts: 3,092
Likes: 120
From: orlando florida
St. Jude Donor '15
Thread Starter
Melting Slicks
Joined: Jul 2004
Posts: 3,092
Likes: 120
From: orlando florida
St. Jude Donor '15
did my upper outer seat foam today. got it in today from corvette america. not too bad to do. 2 zippers and some push clips. they did put some sort of tape stuff to keep it from cutting through. i guess 15 years wasn't too bad.
