problem with blinker
Thread Starter
Burning Brakes
Joined: Jan 2000
Posts: 865
Likes: 0
From: kansas city,MO
problem with blinker
whenever i push the turn signal lever down to signal left the clicking sound is very rapid and the blinker does not work, the bulb works fine with the hazard though, also DRL is off on the left
Safety Car
Joined: Feb 2004
Posts: 4,208
Likes: 2
From: Rochester MN
CI 5-6-7-8 Veteran
St. Jude Donor '04-'05-'06-'07
NCM Ambassador
Originally Posted by MonteHall
mine worked with the hazards as well.. .you have 2 filaments in the bulb... bt it needs to be replaced.
Tech Contributor
Joined: Dec 2003
Posts: 19,384
Likes: 87
From: Horncastle Lincolnshire, England
2023 C5 of the Year Finalist - Unmodified
Once you've rplaced the bulb you may want to consider whether you disable the DRLs. Pulling the A2 fuze will disable them. Just gives a couple of DIC codes for the approach light functions which are lost.
Lots of discussion on pros and cons of DRLs but they do generate a lot of heat. Some members like tham as a safety feature. My opinion is that if the "problem driver" can't see a Vette coming best you go defensive anyhow! JMHO.
Lots of discussion on pros and cons of DRLs but they do generate a lot of heat. Some members like tham as a safety feature. My opinion is that if the "problem driver" can't see a Vette coming best you go defensive anyhow! JMHO.
Team Owner
Joined: Feb 2001
Posts: 21,016
Likes: 0
From: Galveston... well, Santa Fe Texas
Cruise-In VII Veteran
St. Donor '03 & '06
Originally Posted by ptdrummer54
And while you're in there you should check out the housing (especially just above the bulb) - the heat of the bulbs sometimes melts a hole in the housing alowing water to drip on the bulb.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Top 10 Corvette Engines RANKED by Peak Torque (70+ Years of Muscle!)
Joe Kucinski
Corvette ZR1X Will Be Pacing the Indy 500, And Could Probably Race, Too!
Verdad Gallardo
Top 10 Corvettes Coming to Mecum Indy 2026!
Brett Foote
Tech Contributor
Joined: Dec 2003
Posts: 19,384
Likes: 87
From: Horncastle Lincolnshire, England
2023 C5 of the Year Finalist - Unmodified
Replacing the parking light/DRL bulb
Save the money guys!
Turn on the headlights and back off one position to kill the lights.
Unscrew the 3 small screws on the black plastic housing around the headlight. Gently pull the housing clear. Reach down around the headlight unit and release the bulb holder. It unscrews counter clockwise but it has a plastic clip which you need to squeeze to release it. Change the bulb. Reseat the bulb holder and turn until it clicks back in place. Put the plastic housing back in place making sure to locate the small plastic lug in the bracket on the headlamp cover. Replace the 3 screws and close the lights.
10 minute job.
Turn on the headlights and back off one position to kill the lights.
Unscrew the 3 small screws on the black plastic housing around the headlight. Gently pull the housing clear. Reach down around the headlight unit and release the bulb holder. It unscrews counter clockwise but it has a plastic clip which you need to squeeze to release it. Change the bulb. Reseat the bulb holder and turn until it clicks back in place. Put the plastic housing back in place making sure to locate the small plastic lug in the bracket on the headlamp cover. Replace the 3 screws and close the lights.
10 minute job.
Team Owner
Joined: Feb 2001
Posts: 21,016
Likes: 0
From: Galveston... well, Santa Fe Texas
Cruise-In VII Veteran
St. Donor '03 & '06
I'd like to add that I found it tons easier if I removed the hood bumpers just next to the headlights.
BTW I siliconed the head of a 2 inch plastic christmas tree plug over the hole in the top of the light housing... hasn't burned out yet.
BTW I siliconed the head of a 2 inch plastic christmas tree plug over the hole in the top of the light housing... hasn't burned out yet.
