Tools Needed.......buy/borrow
Thread Starter
Melting Slicks
Joined: Jul 2006
Posts: 2,088
Likes: 2
From: tampa florida
Tools Needed.......buy/borrow
My engine sits in my kitchen, the wife is not happy. Looking to buy or borrow the alignment tools for the oil pan and seals and the installation tool for the under drive pulley.
Posted before and someone offered to send it but I think they got busy traveling for work related issues, no worries there at all. So if someone can help me out I would be very appreciative. I'll gladly pay shipping both ways.
alignment tool # J 41480 and J 41476
the pulley tool is a custom made one.
thanks for any help
Posted before and someone offered to send it but I think they got busy traveling for work related issues, no worries there at all. So if someone can help me out I would be very appreciative. I'll gladly pay shipping both ways.
alignment tool # J 41480 and J 41476
the pulley tool is a custom made one.
thanks for any help
Last edited by Brad@RevXtremeAutoSports; Jan 30, 2008 at 09:31 PM.
Burning Brakes
Joined: Jul 2000
Posts: 1,134
Likes: 1
From: Arlington Texas
My engine sits in my kitchen, the wife is not happy. Looking to buy or borrow the alignment tools for the oil pan and seals and the installation tool for the under drive pulley.
Posted before and someone offered to send it but I think they got busy traveling for work related issues, no worries there at all. So if someone can help me out I would be very appreciative. I'll gladly pay shipping both ways.
alignment tool # J 41480 and J 41476
the pulley tool is a custom made one.
thanks for any help
Posted before and someone offered to send it but I think they got busy traveling for work related issues, no worries there at all. So if someone can help me out I would be very appreciative. I'll gladly pay shipping both ways.
alignment tool # J 41480 and J 41476
the pulley tool is a custom made one.
thanks for any help
That was me and I shipped the tools to the address you supplied. Did you receive them? I don't have J41476, but I did ship J41480.
Last edited by thetorch; Jan 31, 2008 at 12:09 AM.
Team Owner
Joined: Mar 1999
Posts: 22,025
Likes: 192
From: At the beach in little Rhody
Brad,
I don't have that one either but I have had some pretty good luck on fleabay. There is one vendor there who deals in Kent Moore tools and is pretty reasonable on prices. He is located in Michigan. If he is not listing it now, he may be able to get it for you and hopefully cheaper.
I don't have that one either but I have had some pretty good luck on fleabay. There is one vendor there who deals in Kent Moore tools and is pretty reasonable on prices. He is located in Michigan. If he is not listing it now, he may be able to get it for you and hopefully cheaper.
Last edited by vettenuts; Jan 31, 2008 at 12:24 PM.
Race Director
Joined: Aug 1999
Posts: 16,935
Likes: 26
From: Lackey, my own dragstrip VA.
Virginia Events Coordinator
Cruise-In IV Veteran
Cruise-In V Veteran
Cruise-In VI Veteran
Cruise-In VII Veteran
NCM Ambassador
Drifting
Joined: Sep 2006
Posts: 1,757
Likes: 13
From: Stillman Valley Illinois
Just make the pulley installationi tool. Call McMaster Carr. You will need the following:
M16-2 threaded rod 300mm long
bag of 16mm "fender" washers
Bag of M16-2 hex nuts
You really only need 3 or 4 hex nuts but they are cheaper by the bag. I ordered mine over the internet; they showed up the next day for a grand total of $ 27.00 including tax and shipping!
M16-2 threaded rod 300mm long
bag of 16mm "fender" washers
Bag of M16-2 hex nuts
You really only need 3 or 4 hex nuts but they are cheaper by the bag. I ordered mine over the internet; they showed up the next day for a grand total of $ 27.00 including tax and shipping!
