Billet Jacking Pucks
Thread Starter
Team Owner
Joined: Mar 1999
Posts: 22,025
Likes: 192
From: At the beach in little Rhody
Billet Jacking Pucks
Was just snooping around in the Mall and found some billet aluminum jacking pucks. Anyone got a set of these? How is the quality and how do they fit? I have the hockey puck set but I think these might be better to put on for when someone doesn't have a set.
Le Mans Master
Joined: Feb 2002
Posts: 6,937
Likes: 21
From: Waldorf MD
Re: Billet Jacking Pucks (vettenuts)
I bought 4 from ZIP. I didn't like idea of the rubber ones, worried about deformation.
They work great. Used them both to jack up and also to place jack stands on. You just twist them 180 degrees and they "lock in", easy to get out also.
They work great. Used them both to jack up and also to place jack stands on. You just twist them 180 degrees and they "lock in", easy to get out also.
CF Old Timer
Joined: May 2000
Posts: 2,035
Likes: 20
From: SF Bay Area Ca
St. Jude Donor '14-'15-'16
Re: Billet Jacking Pucks
I followed the instructions on 97Vette's Page and made my own... I think it cost me $9 total! :cool:
Le Mans Master
Joined: Feb 2002
Posts: 6,937
Likes: 21
From: Waldorf MD
Re: Billet Jacking Pucks (jpvette)
Rather than driving car up on wood blocks (this is always dicey, what with the tires spinning and throwing wood), i use one floor jack, on puck, to jack up car enough to get another floor jack (with a block of wood between jack and car) under center back support to jack up whole rear end.
Le Mans Master
Joined: Feb 2002
Posts: 6,937
Likes: 21
From: Waldorf MD
Re: Billet Jacking Pucks (Along4theRide)
Hey Along4theRide,
-It was his pictures of the pucks under load, that convinced me that I should get solid aluminum ones!
-I couldn't see dropping my vette for $40 difference!
-You really do get them up in the air, it's scary enough without soft pads!
-It was his pictures of the pucks under load, that convinced me that I should get solid aluminum ones!
-I couldn't see dropping my vette for $40 difference!
-You really do get them up in the air, it's scary enough without soft pads!
Burning Brakes
Joined: Mar 2000
Posts: 973
Likes: 0
From: San Jose, CA
Re: Billet Jacking Pucks (jpvette)
Since there are many optional and prefered places to jack up the car, the answer is yes and no. If you are jacking to say, do a tire change in an emergency situation, the chances of you getting a Corvette specialist in a tow truck operator is not very good. Even Chevrolet dealers sometimes dont have the right equipment and knowledge to jack up the Corvette properly, or even if they do, they just ignore it. I personally carry between 2 and 4 of these jacking pucks when I venture out of my garage. While it is l"ess than safe" without jack stands, in a pinch the jacking puck can hold the car up for just a tire swap. Of course the big caveat is not to be under the car when you are doing it this way, for you risk injury and possible death in the worst case, and on the equipment side, damage to body/frame/ suspension parts. So no, not a dumb question at all.
[Modified by ruking1, 9:38 PM 3/1/2002]
[Modified by ruking1, 9:38 PM 3/1/2002]
CF Old Timer
Joined: May 2000
Posts: 2,035
Likes: 20
From: SF Bay Area Ca
St. Jude Donor '14-'15-'16
Re: Billet Jacking Pucks (Oldvetter)
Oldvetter,
I have found them to work just fine and not to deform as much as shown in the photo's ... I however rarely use them and carry them for "just in case" situations mostly. I own a lift and use that way to lift the car unless I need to remove a wheel.
:cheers:
[Modified by Along4theRide, 10:42 PM 3/1/2002]
I have found them to work just fine and not to deform as much as shown in the photo's ... I however rarely use them and carry them for "just in case" situations mostly. I own a lift and use that way to lift the car unless I need to remove a wheel.
:cheers:
[Modified by Along4theRide, 10:42 PM 3/1/2002]
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Burning Brakes
Joined: Jul 1999
Posts: 1,018
Likes: 0
From: The Usual Suspects Yorba Linda Chapter
Re: Billet Jacking Pucks (turboo2u)
Vettenuts
I have 4 billet aluminium jacking pucks from West Coast Corvette. I am interested in selling them if you are interested. I recently put on andy's rocker rails and no longer need the jacking pucks. Let me know if you are interested.
I have 4 billet aluminium jacking pucks from West Coast Corvette. I am interested in selling them if you are interested. I recently put on andy's rocker rails and no longer need the jacking pucks. Let me know if you are interested.
Safety Car
Joined: Sep 2001
Posts: 4,596
Likes: 2
From: Atlanta GA
Re: Billet Jacking Pucks (Oldvetter)
I looked at the ZIP site and didn't see them. Do you have the link?
I bought 4 from ZIP. I didn't like idea of the rubber ones, worried about deformation.
They work great. Used them both to jack up and also to place jack stands on. You just twist them 180 degrees and they "lock in", easy to get out also.
They work great. Used them both to jack up and also to place jack stands on. You just twist them 180 degrees and they "lock in", easy to get out also.
Le Mans Master
Joined: Feb 2002
Posts: 6,937
Likes: 21
From: Waldorf MD
Re: Billet Jacking Pucks (gmblack3)
Here it is:
http://store.yahoo.com/corvetteforum/19jacin.html
By the way, you turn them 90 degrees, not 180.
http://store.yahoo.com/corvetteforum/19jacin.html
By the way, you turn them 90 degrees, not 180.
Le Mans Master
Joined: Jan 2001
Posts: 6,448
Likes: 371
From: Maryville TN
St. Jude Donor '06-13,'16-'17, '19
Re: Billet Jacking Pucks (Oldvetter)
Here it is:
http://store.yahoo.com/corvetteforum/19jacin.html
By the way, you turn them 90 degrees, not 180.
http://store.yahoo.com/corvetteforum/19jacin.html
By the way, you turn them 90 degrees, not 180.
Tom
Safety Car
Joined: Sep 2001
Posts: 4,596
Likes: 2
From: Atlanta GA
Re: Billet Jacking Pucks (TCW)
They show 4 in the picture, I would hope so for $55.
I was thinking of making my own:
http://97vette.com/howto/liftpads/index.html
But I would add some .125 aluminum or stainless steel to the top, bottom and inbetween the hockey pucks. I do like the idea of the added height of the double pucks. Any thoughts?
I was thinking of making my own:
http://97vette.com/howto/liftpads/index.html
But I would add some .125 aluminum or stainless steel to the top, bottom and inbetween the hockey pucks. I do like the idea of the added height of the double pucks. Any thoughts?
Here it is:
http://store.yahoo.com/corvetteforum/19jacin.html
By the way, you turn them 90 degrees, not 180.
Is that price for 1, 2 or 4 pucks? If the ad says, I didn't see it. Thanks.
Tom
http://store.yahoo.com/corvetteforum/19jacin.html
By the way, you turn them 90 degrees, not 180.
Is that price for 1, 2 or 4 pucks? If the ad says, I didn't see it. Thanks.
Tom
Advanced
Joined: Jan 2002
Posts: 65
Likes: 0
Re: Billet Jacking Pucks (RDVT4ME)
RDVT4ME,
I also have the rocker rails. Why don't you need the pucks anymore? Can or would you place a jack on those rails? I too have serious concerns about raising my vette. :eek:
orsadude2
I also have the rocker rails. Why don't you need the pucks anymore? Can or would you place a jack on those rails? I too have serious concerns about raising my vette. :eek:
orsadude2
Thread Starter
Team Owner
Joined: Mar 1999
Posts: 22,025
Likes: 192
From: At the beach in little Rhody
Re: Billet Jacking Pucks (Orsadude2)
QUOTE]RDVT4ME,
I also have the rocker rails. Why don't you need the pucks anymore? Can or would you place a jack on those rails? I too have serious concerns about raising my vette. :eek:
orsadude2[/QUOTE]
Yes, guess I am curious about the same thing.[
I also have the rocker rails. Why don't you need the pucks anymore? Can or would you place a jack on those rails? I too have serious concerns about raising my vette. :eek:
orsadude2[/QUOTE]
Yes, guess I am curious about the same thing.[
Thread Starter
Team Owner
Joined: Mar 1999
Posts: 22,025
Likes: 192
From: At the beach in little Rhody
Re: Billet Jacking Pucks (Lil Red)
Hey RDVT4ME,
i'm interested in buying your pucks if they are still available!
[Modified by Lil Red, 9:43 AM 3/3/2002]
i'm interested in buying your pucks if they are still available!
[Modified by Lil Red, 9:43 AM 3/3/2002]
