absfixer or module master??
Thread Starter
Racer
Joined: Jan 2013
Posts: 265
Likes: 16
From: Columbus ga
absfixer or module master??
Need help guys.... I just got my abs module off (havent even cleaned the blood off my forearms yet) and want to know which place is best?
Module master says they have a five year guarantee and a couple folks on the forum have mentioned absfixer. There is one here in Ga myairbags.com that say they do it also with lifetime warranty and half the price. Want it fixed right the first time so willing to pay the higher price....
Need anybodys opinion, gonna mail out to one of them in the morning.
Thanks guys and gals!!
Module master says they have a five year guarantee and a couple folks on the forum have mentioned absfixer. There is one here in Ga myairbags.com that say they do it also with lifetime warranty and half the price. Want it fixed right the first time so willing to pay the higher price....
Need anybodys opinion, gonna mail out to one of them in the morning.
Thanks guys and gals!!
Thread Starter
Racer
Joined: Jan 2013
Posts: 265
Likes: 16
From: Columbus ga
Why not repair it yourself and save a lot of money???
http://forums.corvetteforum.com/c5-t...r-fleabay.html
http://forums.corvetteforum.com/c5-t...r-fleabay.html
thanks.
Tech Contributor
Joined: Oct 1999
Posts: 41,058
Likes: 9,817
From: Charlotte, NC (formerly Endicott, NY)
What failure code caused you to remove the module? If it was C1214 did you also check the BPMV motor circuit to see if it was shorted to the BPMV case? If the circuit is shorted to the case that causes an excessive current draw through the relay in the EBCM thus causing the C1214 and you the BPMV will have to be replaced as well or the failure will come back when the excessive current burns the replacement relay in the repaired EBCM. To check the BPMV you have to disconnect the BPMV output harness and check the resistance from wires to the BPMV case. If you measure any thing but Infinity then the BPMV is bad.
Bill
Bill
Melting Slicks
Joined: Apr 2009
Posts: 2,479
Likes: 36
I used Module Master two years ago and my EBCM is still going strong. Their service was excellent. I actually purchased a complete rebuilt EBCM from them because I wanted to hold on to my original one as backup. They sent me one fairly quickly and it only cost me $250.00.
Team Owner
Joined: May 2003
Posts: 23,480
Likes: 9
From: East Meadow NY
St. Jude Donor '12
Thread Starter
Racer
Joined: Jan 2013
Posts: 265
Likes: 16
From: Columbus ga
I used Module Master two years ago and my EBCM is still going strong. Their service was excellent. I actually purchased a complete rebuilt EBCM from them because I wanted to hold on to my original one as backup. They sent me one fairly quickly and it only cost me $250.00.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Burning Brakes
Joined: Jul 2009
Posts: 976
Likes: 53
From: smyrna de
Why not repair it yourself and save a lot of money???
http://forums.corvetteforum.com/c5-t...r-fleabay.html
http://forums.corvetteforum.com/c5-t...r-fleabay.html
Thread Starter
Racer
Joined: Jan 2013
Posts: 265
Likes: 16
From: Columbus ga
I wish I was that mechanically inclined....I just changed out my plugs and doing the belt this weekend... thats about the extent of my knowledge, could not have done that without the help of this forum!!
I was impressed I didnt mess anything up doing the plugs!!!!
Thanks for the advice anyway I will be asking again!!!
Thanks
I was impressed I didnt mess anything up doing the plugs!!!!
Thanks for the advice anyway I will be asking again!!!
Thanks