Rear Diffuser - Pic Request
Thread Starter
Racer
Joined: Jun 2013
Posts: 427
Likes: 111
From: Raleigh NC
I was at the OC MD Corvette weekend this past week, hoping to see some different ones and there wasn't a lot of modded cars out there, unfortunately. I saw the V1 of this one, 3 vertical downward fins, but I wasn't a fan of how it attached.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
Drifting
Joined: Jun 2016
Posts: 1,325
Likes: 325
2020 Corvette of the Year Finalist (track prepared)
C7 of Year Winner (track prepared) 2019
I was at the OC MD Corvette weekend this past week, hoping to see some different ones and there wasn't a lot of modded cars out there, unfortunately. I saw the V1 of this one, 3 vertical downward fins, but I wasn't a fan of how it attached.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
Difflow has an updated "track" version of their design now!
I have it just haven't installed it yet the car is at the fab shop getting the cage finished.
will update when i get it back.
E-Ray, 3LZ, ZER, LIFT
Joined: Sep 2007
Posts: 35,045
Likes: 12,412
From: NE South Carolina
I was at the OC MD Corvette weekend this past week, hoping to see some different ones and there wasn't a lot of modded cars out there, unfortunately. I saw the V1 of this one, 3 vertical downward fins, but I wasn't a fan of how it attached.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
Below is a pic of my C7 Carbon diffuser. This is a PDF of my install with lots of tech info on diffusers: http://netwelding.com/Rear_Diffuser.pdf
Last edited by JerryU; Dec 2, 2018 at 01:07 PM.
Le Mans Master
Joined: Oct 2009
Posts: 7,397
Likes: 124
From: Frisco TX
I was at the OC MD Corvette weekend this past week, hoping to see some different ones and there wasn't a lot of modded cars out there, unfortunately. I saw the V1 of this one, 3 vertical downward fins, but I wasn't a fan of how it attached.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
I am thinking the C7 Carbon one with the under tray or the Difflow might be the way to go.
Thread Starter
Racer
Joined: Jun 2013
Posts: 427
Likes: 111
From: Raleigh NC
The way it was attached to the car didnt look right. You could see gaps from where the seal around the edges wasn't flush. I saw it on 3 different cars. The one that looked good the guy only drove it about 4500 a year he said. The others were driven a good bit more.
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Every 2027 Corvette Engine Explained
Joe Kucinski
Designer Imagines A Corvette That Looks More Like a Corvette Than the Corvette
Verdad Gallardo
10 Ugly Corvettes That We Still Kinda Love
Joe Kucinski
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Le Mans Master
Joined: Oct 2009
Posts: 7,397
Likes: 124
From: Frisco TX
I have the V2 pictured above and it looks perfect... No gaps etc.
Melting Slicks
Joined: Oct 2017
Posts: 2,006
Likes: 330
From: North Carolina
Melting Slicks
Joined: Oct 2017
Posts: 2,006
Likes: 330
From: North Carolina
Melting Slicks
Joined: Oct 2017
Posts: 2,006
Likes: 330
From: North Carolina
Thread Starter
Racer
Joined: Jun 2013
Posts: 427
Likes: 111
From: Raleigh NC
Meh, I wasn't an overall a fan of the stick on look and how much the outer edges protruded for me. As a result I ordered the Katech strakes from Performance Corvettes along with an X pipe. The X pipe got here in two days, just waiting on the strakes now. Fun winter projects ahead!
Le Mans Master
Joined: Oct 2009
Posts: 7,397
Likes: 124
From: Frisco TX
Le Mans Master
Joined: Oct 2009
Posts: 7,397
Likes: 124
From: Frisco TX
Meh, I wasn't an overall a fan of the stick on look and how much the outer edges protruded for me. As a result I ordered the Katech strakes from Performance Corvettes along with an X pipe. The X pipe got here in two days, just waiting on the strakes now. Fun winter projects ahead!
That diffuser is a complete 1 piece bumper/diffuser unit in carbon fiber.
There is nothing stuck on about it.
Not sure we are talking about the same thing.
APR V2