CorvetteForum - Chevrolet Corvette Forum Discussion
0 2019/01/20 11:18:25
0 2019/03/20 18:41:50
0 2019/01/20 11:18:26
0 2019/03/20 18:53:20
0 2019/03/20 18:53:26
0 2019/01/21 10:08:21
A peak inside through the filler. Everything looks to be in place.
A peak inside through the filler. Everything looks to be in place.
0 2019/03/21 17:48:16
Tank all buttoned up. Still have to wire the fuel pump, but I’ll do that once the engine is installed.
Tank all buttoned up. Still have to wire the fuel pump, but I’ll do that once the engine is installed.
0 2019/03/21 17:48:29
These will be recovered in black with silver inserts and the ‘64 nose emblem embroidered in the head rest. They also allow me to use silver four point belts with the shoulder harness attached to the roll bar.
These will be recovered in black with silver inserts and the ‘64 nose emblem embroidered in the head rest. They also allow me to use silver four point belts with the shoulder harness attached to the roll bar.
0 2019/01/22 13:15:43
I dropped the front bumpers, brackets, grill, trim and BB hood grills off for matte black powder coating. Should be ready next week and I’ll drop off the rear brackets and rocker trim.
I dropped the front bumpers, brackets, grill, trim and BB hood grills off for matte black powder coating. Should be ready next week and I’ll drop off the rear brackets and rocker trim.
0 2019/01/22 13:15:46
I didn’t remember the original tank filler neck being this far off center? Anyone? Anyone? Bueller?
I didn’t remember the original tank filler neck being this far off center? Anyone? Anyone? Bueller?
0 2019/03/21 17:48:35
I thought my original bellhousing was painted black. Turned out it was just 55 years of grease and crud. She sparkles now!
I thought my original bellhousing was painted black. Turned out it was just 55 years of grease and crud. She sparkles now!
0 2019/03/21 17:48:47
0 2019/01/23 08:48:42
0 2019/01/23 11:53:30
0 2019/01/23 11:53:30
Say hello to my little friend.
Say hello to my little friend.
0 2019/03/21 17:49:03
That’s pretty good 541hp @5800rpm. Should scoot.
That’s pretty good 541hp @5800rpm. Should scoot.
0 2019/03/21 17:49:10
0 2019/01/23 13:20:11
Rear Wilwood caliper on my coupe gravity bleeding. The inside bleeder is complete, the outside still has air.
Rear Wilwood caliper on my coupe gravity bleeding. The inside bleeder is complete, the outside still has air.
0 2019/03/22 06:01:22
0 2019/01/23 13:20:11
But to completely bleed them, I removed them and hung them vertically. I bench bled the mc on the car and then gravity bled the entire system which is completely new from the mc to the brake lines to the calipers.
But to completely bleed them, I removed them and hung them vertically. I bench bled the mc on the car and then gravity bled the entire system which is completely new from the mc to the brake lines to the calipers.
0 2019/03/22 06:01:29
0 2019/01/23 13:20:12
0 2019/03/22 12:20:59
No so bad and still fully functional. I had to release the straps in order to get the last filler neck screws installed and torqued. That was a bear.
No so bad and still fully functional. I had to release the straps in order to get the last filler neck screws installed and torqued. That was a bear.
0 2019/03/23 15:00:32
0 2019/01/23 13:20:16
0 2019/01/23 13:20:16
Quality components, well assembled.
Quality components, well assembled.
0 2019/03/23 15:00:46
And this instead of the crossed C5 flags.
And this instead of the crossed C5 flags.
0 2019/01/23 20:42:55
Is a theme starting to emerge?
Is a theme starting to emerge?
0 2019/03/23 15:00:59
I always loved these valve covers.
I always loved these valve covers.
0 2019/03/23 15:01:06
Imagine a silver insert.
Imagine a silver insert.
0 2019/01/23 20:42:59
0 2019/01/23 21:03:11
I’ll install the a/c compressor once the engine is installed.
I’ll install the a/c compressor once the engine is installed.
0 2019/03/24 12:38:47
I’m glad Borgeson sells their ps conversion without the pump and bracket.
I’m glad Borgeson sells their ps conversion without the pump and bracket.
0 2019/03/24 12:39:04
0 2019/01/24 05:36:35
Sometimes it’s the little things that slow you down. I don’t have VC gaskets! I added them to my Summit order along with black wires, a black distributor cap, thermostat and plain aluminum water neck.
Sometimes it’s the little things that slow you down. I don’t have VC gaskets! I added them to my Summit order along with black wires, a black distributor cap, thermostat and plain aluminum water neck.
0 2019/03/24 12:39:20
Sneak peak at a seat.
Sneak peak at a seat.
0 2019/01/24 13:50:10
0 2019/03/28 14:12:22
My trust Millermatic welder.
My trust Millermatic welder.
0 2019/01/24 13:50:11
Once the diff arrives from Currie I can install it in the housing and Jack the entire assembly in place, set my pinion angle, check clearances and weld the new pinion mount in place. The cradle uses a Heim end here and two more that mount to a bracket I will weld to crossmember #4 once everything is in place.
Once the diff arrives from Currie I can install it in the housing and Jack the entire assembly in place, set my pinion angle, check clearances and weld the new pinion mount in place. The cradle uses a Heim end here and two more that mount to a bracket I will weld to crossmember #4 once everything is in place.
0 2019/01/24 13:50:12