CorvetteForum - Chevrolet Corvette Forum Discussion
I made the bend around an 1/8" rod to fit the frame of the vent window. Note the fold / bend does not make a complete bend. See the sketch
I made the bend around an 1/8" rod to fit the frame of the vent window. Note the fold / bend does not make a complete bend. See the sketch
0 2026/01/08 07:10:22
0 2026/01/08 07:10:43
Wraps around the wing frame. May want to use a softener e.g., Scotch 33+ electrical tape inside the groove of the bracket.
Wraps around the wing frame. May want to use a softener e.g., Scotch 33+ electrical tape inside the groove of the bracket.
0 2026/01/08 08:21:11
Tab on the back of the bracket slips behind the weatherstripping. Carefully slip a wedge in to open a gap if none exists to slide the tab down.
Tab on the back of the bracket slips behind the weatherstripping. Carefully slip a wedge in to open a gap if none exists to slide the tab down.
0 2026/01/08 08:23:11
Gap at the windshield trim. Considering a rubber spacer glued to the bracket to prevent movement forward if it comes forward in use.
Gap at the windshield trim. Considering a rubber spacer glued to the bracket to prevent movement forward if it comes forward in use.
0 2026/01/08 08:25:44
Absolutely no bugs here.
Absolutely no bugs here.
0 2026/01/12 13:52:56
0 2026/01/12 14:28:10
0 2026/01/12 14:28:24
Known original 68 327. Less than 1/2" clearance for the radiator hose on the thermostat housing.
Known original 68 327. Less than 1/2" clearance for the radiator hose on the thermostat housing.
0 2026/01/13 05:01:59
GM 3877660 thermostat housing.
GM 3877660 thermostat housing.
0 2026/01/13 05:03:04
Can't be over a couple of bucks $$. If you want them and can't find them locally, PM me.
Can't be over a couple of bucks $$. If you want them and can't find them locally, PM me.
0 2026/01/13 05:11:53
0 2026/01/13 05:12:12
0 2026/01/18 14:06:00
0 2026/01/20 09:51:09
0 2026/01/20 09:51:56
0 2026/01/20 09:53:03
0 2026/01/20 09:53:23
0 2026/01/24 06:19:35
0 2026/01/28 09:20:39
0 2026/01/30 07:13:33
0 2026/01/30 07:13:48
0 2026/02/12 07:31:55
0 2026/02/12 07:32:10
Couldn't get a good clear picture, but hope this helps.
Couldn't get a good clear picture, but hope this helps.
0 2026/02/15 06:51:28
0 2026/02/18 12:03:15
0 2026/02/18 12:03:40
0 2026/02/18 12:03:56
Motor pinion screw adjustment????
Motor pinion screw adjustment????
0 2026/02/19 15:40:27
Front seal of one piece rubber pan gasket
Front seal of one piece rubber pan gasket
0 2026/02/21 15:24:11
No words can explain my regret for using this new technology. Also seeps along the sides of the pan.
No words can explain my regret for using this new technology. Also seeps along the sides of the pan.
0 2026/02/21 15:25:08
0 2026/02/22 09:37:21
Air cleaner base with fresh air tube and 1" rubber hose..
Air cleaner base with fresh air tube and 1" rubber hose..
0 2026/02/25 09:57:33
Fresh air tube to engine block
Fresh air tube to engine block
0 2026/02/25 09:58:12
Original 3367 Holley with air cleaner base and fresh air tube shot.
Original 3367 Holley with air cleaner base and fresh air tube shot.
0 2026/02/25 09:58:42
0 2026/02/26 13:50:39
5/8" hose fitting. has internal baffle. A grommet would be needed to fit in the hole a the back of the block.
5/8" hose fitting. has internal baffle. A grommet would be needed to fit in the hole a the back of the block.
0 2026/02/26 14:08:03
Plumb bob down from ends of horizontal bar to make marks for setting toe-in. Camber gauge or even a level to set camber and caster.
Plumb bob down from ends of horizontal bar to make marks for setting toe-in. Camber gauge or even a level to set camber and caster.
0 2026/03/04 07:18:03
Homemade tool to check caster.
Homemade tool to check caster.
0 2026/03/04 07:18:28
Yellowish residue on the intake - fuel???
Yellowish residue on the intake - fuel???
0 2026/03/04 07:46:03
Yellowish residue on the intake at thermostat housing. ????
Yellowish residue on the intake at thermostat housing. ????
0 2026/03/04 07:46:27