CorvetteForum - Chevrolet Corvette Forum Discussion
It is about 1-1/2" x 2-1/4" foam about 1/16" thick.
It is about 1-1/2" x 2-1/4" foam about 1/16" thick.
0 2019/11/06 05:57:23
There is no glue on it. There are light indentations on one side that look like arrows point outward.
There is no glue on it. There are light indentations on one side that look like arrows point outward.
0 2019/11/06 05:57:36
0 2019/11/08 14:46:08
Moments I missed.
Moments I missed.
0 2019/11/11 16:08:48
Hard times deserve rest.
Hard times deserve rest.
0 2019/11/11 16:08:57
She taught him how to race.
She taught him how to race.
0 2019/11/11 16:09:25
0 2019/11/13 11:32:51
In daylight with garage door open - brakes not applied
In daylight with garage door open - brakes not applied
0 2019/11/20 07:13:02
In daylight with garage door open - brakes on LED infused red lights on outside & LED red bulbs inside with white brake light lenses.
In daylight with garage door open - brakes on LED infused red lights on outside & LED red bulbs inside with white brake light lenses.
0 2019/11/20 07:13:33
Infused LED lights in the original positions only
Infused LED lights in the original positions only
0 2019/11/20 07:14:44
Camber gauge added to toe bar
Camber gauge added to toe bar
0 2019/11/27 05:47:51
Toe bar held to wheel with magnets
Toe bar held to wheel with magnets
0 2019/11/27 05:48:03
Caster guage hooks on upper and lower ball joint zerks. Adjustable 1/2" threaded rod to work on Camaro or Vette. A PIA to hold plumb in two directions while obtaining measurement.
Caster guage hooks on upper and lower ball joint zerks. Adjustable 1/2" threaded rod to work on Camaro or Vette. A PIA to hold plumb in two directions while obtaining measurement.
0 2019/11/27 07:31:11
Fixed end of caster guage. Must be square with threaded rod.
Fixed end of caster guage. Must be square with threaded rod.
0 2019/11/27 07:31:26
Sliding end of caster guage (square with threaded rod) to measure difference between upper and lower ball joint centers - and calculate caster.
Sliding end of caster guage (square with threaded rod) to measure difference between upper and lower ball joint centers - and calculate caster.
0 2019/11/27 07:31:38
Slip pads - 2 pcs of plastic or metal with zip lok bag filled with 5 or 6 shots of chassis grease. One under each wheel
Slip pads - 2 pcs of plastic or metal with zip lok bag filled with 5 or 6 shots of chassis grease. One under each wheel
0 2019/11/27 07:32:05
Water level made from 10 feet of 3/8" vinyl tubing, 2ea 90 deg elbows, and scrap wood routed for tubing. Water is dyed blue. I also use it to level my pool table.
Water level made from 10 feet of 3/8" vinyl tubing, 2ea 90 deg elbows, and scrap wood routed for tubing. Water is dyed blue. I also use it to level my pool table.
0 2019/11/27 07:32:18
Caster guage in use - must be plumb both directions.
Caster guage in use - must be plumb both directions.
0 2019/11/27 08:12:16
Magnetic level on the guage helps.
Magnetic level on the guage helps.
0 2019/11/27 08:12:24
Leaf Block - page wire fence
Leaf Block - page wire fence
0 2019/11/28 14:14:49
Wind raked back yard - I don't have to do the 4th pass with the leaf vac.
Wind raked back yard - I don't have to do the 4th pass with the leaf vac.
0 2019/11/28 14:15:44
0 2019/12/05 18:18:29
0 2019/12/05 18:18:56
0 2019/12/26 08:24:04
Wheels turned fully to the left and cable loop installed over the bolt in the coupler and then the flanged nut installed. I found the nut is not necessary, but not much trouble.
Wheels turned fully to the left and cable loop installed over the bolt in the coupler and then the flanged nut installed. I found the nut is not necessary, but not much trouble.
0 2019/12/26 08:25:41
Won't work if Godzilla is at the wheel and breaks the cable or 3/8" bolt, but I also have a 'CLUB' on the steering wheel that they will use bolt cutters on.
Won't work if Godzilla is at the wheel and breaks the cable or 3/8" bolt, but I also have a 'CLUB' on the steering wheel that they will use bolt cutters on.
0 2019/12/26 08:25:48
Cable bolted to exhaust manifold bolt hanging loose.
Cable bolted to exhaust manifold bolt hanging loose.
0 2019/12/26 08:26:48
60s sheep horn Chevy Drivers side
60s sheep horn Chevy Drivers side
0 2020/01/10 09:53:48
This will put the alternator in the right place. Notice the front bolt hole is slotted but not the rear.
This will put the alternator in the right place. Notice the front bolt hole is slotted but not the rear.
0 2020/01/10 09:53:56
68RS Camaro mounting, The bracket is basically the same, but curved to clear the manifold runner and lower the alternator. These are not sheep horn manifolds
68RS Camaro mounting, The bracket is basically the same, but curved to clear the manifold runner and lower the alternator. These are not sheep horn manifolds
0 2020/01/10 09:56:28
68RS mounting at the front.
68RS mounting at the front.
0 2020/01/10 09:58:41
660 switch and connector
660 switch and connector
0 2020/05/07 15:32:54
clear / white connector original??
clear / white connector original??
0 2020/05/07 15:37:29
Clip on the manifold bolt.
Clip on the manifold bolt.
0 2020/07/19 15:58:16
Molded hose with a little more than 90.
Molded hose with a little more than 90.
0 2020/07/19 15:59:23
Cruise Control unit on hood latch bracket
Cruise Control unit on hood latch bracket
0 2020/08/09 18:32:43
One way of tying to the throttle lever
One way of tying to the throttle lever
0 2020/08/09 18:33:30
More than 50 ft of extra wire
More than 50 ft of extra wire
0 2020/08/09 18:34:05
Homemade jig for camber and toe-in
Homemade jig for camber and toe-in
0 2020/09/09 07:05:20
Making friends. Kids were the losers on both sides of the pond.
Making friends. Kids were the losers on both sides of the pond.
0 2020/11/11 19:06:32