Engine compartment paint
Thread Starter
Racer
Joined: Mar 2013
Posts: 298
Likes: 2
From: Orange Park Florida
Engine compartment paint
Does anyone have any recommendation for engine compartment paint. I been using spray cans but it gets dirty and holds dust real bad and then it looks dingy. Any help would be appreciated
Team Owner
Joined: Sep 2006
Posts: 31,286
Likes: 4,375
From: Westminster Maryland
Hi C400,
Are you using flat or semi-flat black paint?
The original paint used was semi-flat black.
Most people find semi-flat much easier to maintain than flat.
The paints mentioned often here are Krylon #1613 (not the new formula #51613), John Deere Blitz Black, and SEM Semi-flat black.
Good Luck!
Regards,
Alan
Are you using flat or semi-flat black paint?
The original paint used was semi-flat black.
Most people find semi-flat much easier to maintain than flat.
The paints mentioned often here are Krylon #1613 (not the new formula #51613), John Deere Blitz Black, and SEM Semi-flat black.
Good Luck!
Regards,
Alan
Thread Starter
Racer
Joined: Mar 2013
Posts: 298
Likes: 2
From: Orange Park Florida
Hi C400,
Are you using flat or semi-flat black paint?
The original paint used was semi-flat black.
Most people find semi-flat much easier to maintain than flat.
The paints mentioned often here are Krylon #1613 (not the new formula #51613), John Deere Blitz Black, and SEM Semi-flat black.
Good Luck!
Regards,
Alan
Are you using flat or semi-flat black paint?
The original paint used was semi-flat black.
Most people find semi-flat much easier to maintain than flat.
The paints mentioned often here are Krylon #1613 (not the new formula #51613), John Deere Blitz Black, and SEM Semi-flat black.
Good Luck!
Regards,
Alan
Thanks Alan
Team Owner
Joined: Jan 2006
Posts: 37,637
Likes: 3,118
From: Crossville TN
I suspect that either your parts have not been cleaned thoroughly, or that the paint is not being sprayed fully (usually needs one light coat, followed by a second 'wet' coat after a few minutes drying time).
If you don't get full coverage with your paint, it will look 'fuzzy' and not smooth out. I've not had any problem with any of the paints listed by Alan71.
If you don't get full coverage with your paint, it will look 'fuzzy' and not smooth out. I've not had any problem with any of the paints listed by Alan71.
Team Owner
Joined: Sep 2006
Posts: 31,286
Likes: 4,375
From: Westminster Maryland
Hi C400,
That surprises me!
Are you sure it's #1613 and not #51613?
The vast majority of the engine compartments and wheel wells I see that I think look good have semi-flat paint on them.
Flat isn't a surface that's easy to maintain, nor is 51613.
Regards,
Alan
If the paint used is too glossy it really begins to show the compartment's and wheel wells' imperfections.
That surprises me!
Are you sure it's #1613 and not #51613?
The vast majority of the engine compartments and wheel wells I see that I think look good have semi-flat paint on them.
Flat isn't a surface that's easy to maintain, nor is 51613.
Regards,
Alan
If the paint used is too glossy it really begins to show the compartment's and wheel wells' imperfections.
Thread Starter
Racer
Joined: Mar 2013
Posts: 298
Likes: 2
From: Orange Park Florida
Hi C400,
That surprises me!
Are you sure it's #1613 and not #51613?
The vast majority of the engine compartments and wheel wells I see that I think look good have semi-flat paint on them.
Flat isn't a surface that's easy to maintain, nor is 51613.
Regards,
Alan
If the paint used is too glossy it really begins to show the compartment's and wheel wells' imperfections.
That surprises me!
Are you sure it's #1613 and not #51613?
The vast majority of the engine compartments and wheel wells I see that I think look good have semi-flat paint on them.
Flat isn't a surface that's easy to maintain, nor is 51613.
Regards,
Alan
If the paint used is too glossy it really begins to show the compartment's and wheel wells' imperfections.
Thread Starter
Racer
Joined: Mar 2013
Posts: 298
Likes: 2
From: Orange Park Florida
Corvette Stories
The Best of Corvette for Corvette Enthusiasts
Top 10 Most Expensive Corvettes Ever Sold on Bring A Trailer
Brett Foote
10 Things Every Corvette Owner Needs (2026 Edition)
Michael S. Palmer
8 Most "Only Corvette Owners Understand" Quirks and Problems
Pouria Savadkouei
10 Reasons the C6 Z06 is Still A Performance Benchmark After 20 Years
Joe Kucinski
How Much Horsepower Every Corvette Engine "LOST" in 1972
Joe Kucinski
Top 10 DOs and DON'Ts for Protecting Your Convertible Top!
Michael S. Palmer
Top 10 Most Explosive Corvettes Ever Made: Power-to-Weight Ratio Ranked!
Joe Kucinski
150 hp to 1,250 hp: Every Corvette Generation Compared by the Specs That Matter
Joe Kucinski
8 Coolest Corvette Pace Cars (and Replicas) of All Time
Verdad Gallardo
Racer
Joined: Jul 2010
Posts: 430
Likes: 31
From: Ontario
I restore vintage JD garden tractors so I'm familiar with the paint Mother Deere sells. Blitz black is excellent quality but a little too flat for me. Tends to get chalky looking after several years. I use JD black semi-gloss instead. The low level shine is just about right and very easy to maintain. When it's dry it looks pretty much the same as the low gloss black factory powder coating you see on new barbeques. I've used it under the hoods of my bigger toys and I especially like it for doing brackets and various small parts. I lay it on in nice thin coats and then go just a tad thicker on the last pass. Best thing to do is buy a rattle can of each, try them and decide for yourself. You may want to use the semi-gloss in some areas and the flat in others. What I like about both paints is they're very consistent over time. When I paint something with them now they look (and go on) the same as something else I painted years ago. Not that I can paint anything right now. Man I hate winter.
Last edited by army; Feb 20, 2015 at 03:05 PM.
