Ok boyz...lets here the parts list for this years changes

For me:

- New iForged Black TE-7 wheels
- 80lb injectors.....
- Cartek Flip Drive
- Advanced Technologies Twin Disk Clutch
- Remote Clutch Bleeder
- My new Z06 decals by Austin
- Harland Sharpe Rockers
- 335/30/19 Nitto NT05's



your turn

 

Ah.......!!...????.....ummm......ahhhhhh hh.......

 

Most likely new Radiator and oil cooler. Haven't decided if I want integrated or separate. I may try to build a shorter radiator and modify the intake to the Vortech to accomodate a 4" inlet. It should be good for a few more HP.
New RPS triple carbon clutch hopefully coming in next week from LG Motorsports.
Fix my A/C
New Drag Radials. Possibly M&H or maybe BFG 345/30/18's

 

Ok here goes,
1. 6.0 iron block with forged bottom end 370 cid and lQ9 heads ported and polished by Jeff @THP, along with my intake and throttle body being ported and polished
2. 2004 zo6 3:42 differential
3. z06 leaf springs
4. hardened tunnel plate
5. turn signal mirrors
6. remote clutch bleeder
7.L5 Fender flares
8. C6 ZO6 motorsport wheels
9. C6 ZO6 brake caliper, rotors and lines
10. breathless performance brake ducts
11. tigershark front end
12. ACI door sill extensions
13. heated seat and message inserts
14. coil pack covers with laser cut writing
15. mccloed twin disk clutch and flywheel
16. chrome door sill inserts
17. lambo door hinges
18. turbtronixs supersonicblowoff valve
19. greddy boost controller
20. sound and heat insulation
21. twin wet NOS injection
22. paint job
23. lost of upgraded parts for engine build, yella terra 1.8 ultralight rockers, melling oil pump, lloyd timing chain, two piece timing chain cover, LS7 lifters, black magic fuel rails, 83lb injectors, along with all part including block being powdercoated
24. convertable top
25. rpm scatter shield
26. roll bar
27. leather wrapping my center console and radio bezel. (carskinz) along with a new steeringwheel
28. cradles and tunnel plate are going to be powdercoated along with the exhaust.
29. headers are going to be ceramic powdercoated inside and out
30. shorty antenna
31. line lock
32. bikini bolsters, and two tone armrests
33. new fender decals
34. raptor shifter light
35. I think that is it. I have most of the stuff sitting in my garage waiting to be installed. I am waiting for the engine to arrive so I can start tearing this puppy down and get the party started. All work is going to be done by me. It should be done and on the street by spring.

 

2009 Spider wheels
new intake for the KB
spray bar setup after the intercooler
RPM stage 5 trans
Quaiffe rear diff (3.15)
Solid TT bushings
Get the rear L5 fenders put on
TS front end
paint job
and I am done!!!!!!

 

sc600

 

Cartek Flip Drive

RPM A4 Level IV Tranny

New Dyno Tune

Possibly 60lb Injectors (Want a deal on a set!

Thanks,Matt

 

Rebuild locked tranny with most of the usual upgrades
01+ Torque Tube swap
Quicktime SFI Bellhousing
Pfadt motor mounts and diff mount
A few interior and sound deadening mods

 

I will have my 60# motorons avaliable very soon ! I will let ya know

Less than 3500 miles on them !

 

C5 FI Section, the anti-recession.

 

Here is my wishlist:

1. New TOYO RA1s
2. A&A new I/C (when price goes down )
3. on the fence for a CAM change
4. Oil Cooler (like Bret, don't know if integrated or separate is the route)
5. new BOV (Tial 50mm)
6. All Fluids changed to Royal Purple
7. Going to mod for 50 more rwhp in order to achieve 800
8. Change out the JT to a YSi

 

+40 cubic inches
+100 rwhp
Flip drive
Bigger headers and catback
At least 3 sets of NT01's

 

3.9 Pulley
Cartek Flip drive
and hopefully upgrade the P1

 

I just put oil in the Procharger need to install a check valve on my fuel system and add a oil cooler.

 

Holy smokes Jason, that's one huge "to-do" list!

Drew, is IForged making custom TE7s for you or are you running 1/4" spacers to clear the C6 Z06 brakes?

I was thinking of some black TE7s as well but was told they will need 1/4" spacers on the normal 18x9.5 and 19x11 set-up.

My list is not too bad,
1) MCM Carbon fiber hood
2) Caravaggio seats (already in. black with red Z06 insignia's)
3) A&A stage 2 upgrade kit with new ram air intercooler, black piping and red couplers. Standing rad back up at he same time.
4) custom made projector headlights (retaining pop-up feature)
5) If my wheels sell, C6 Z06 brakes and new wheels (undecided)

Tyler

 

-SC set-up
-New fuel system
-Meth Injection
-8-rib

Hopefully that will get me where I want it

 

Hey bud

Iforged did realize that the big brake kit would cause an issue so the are making the rears a 53mm offset which on their computer renderings should be good enough to clear. Basically 1/4 of an inch or 7mm they will protrude from the wheel well. I think the fronts were OK. I do not have the wheels yet but once I do I will post pics I have been gaurenteed a full $ refund if they do not fit as this was a major concern of mine when buying them.
I am using Stephen who is a supporting vendor on this site for these wheels.

Give him a shout with your questions, he has been great to deal with

stefan@d2autosport.com

 

smaller supercharger pulley
UD crank pulley
FMIC
LS6 Intake
Ported TB
New Tune


Hopefully it won't be time for a new motor for awhile longer...

 

Just got her back from A&A with this years mods.

new ram air intercooler
3.1 s/c pulley
ACT twin disc clutch
retune

new numbers are 749 rwhp
722 rwtq

peak numbers aren't alot better but mid range tq is

 

2009 Mod List

- Finish up the body work and paint.
- Get the new interior in, including C6 seats, stereo system and leather interior upgrade
- Finish up suspension mods.
- Install Forged 416 motor and some sort of FI system
- Fuel System
- Complete re-wiring of interior
- Install some Engine Bling

Then it's time to take a long break.