Finally finished my C5 build (Stroker / Supercharger / Brakes / Wheels / Interior)
#1
Burning Brakes
Thread Starter
Finally finished my C5 build (Stroker / Supercharger / Brakes / Wheels / Interior)
Built By RAGIN' RACIN'
-2001 Corvette C5 with 27,000 original miles on car (300 miles on modifications)
874HP / 736TQ
Texas Speed & Performance 383ci Engine 10:1 compression
-TSP 230/242 .600 .600 114lsa +2 Cam (Engineered By "Pat G" for Application)
-Texas Speed Forged 4340 Crankshaft, 6-Bolt Flange
-TSP 6.125" Super I-Beam Forged Rods w/ ARP L19 Bolts
-Wiseco -15cc Dish Forged Aluminum Pistons
-Wiseco Tool Steel Wrist Pins
-Johnson 2110r Lifters
-Rollmaster Billet Timing Gear Set & Chain
-Melling oil pump 10296
-All new GM sensors / new GM water pump / all new GM seals & gaskets
-TSP Chromoly Pushrods
-ARP Main Stud Kit / ARP Head Stud Kit / ARP accessory mounting bolts / ARP clutch bolts
-Improved Racing C5 Corvette "Batwing Oil Pan" Crank Scraper
-FAST 92mm Intake w/ LS7 Throttle Body
-Stainless Braided Hose Steam Vent Kit For Cylinder Heads
-60lb Injectors
-Gen IV Engine Block w/ 24 Reluctor Wheel
-PRC 220cc "CNC" Heads, Flow 315 CFM Intake / 230 CFM Exhaust @ .650
*62cc, 2.045" Intake / 1.600" Stainless Valves, TSP .660" Dual PAC Spring
Kit, Ti Retainers, TSP 1.72" Roller Rockers w/trunion upgrade
A&A V3 Ti Trim Supercharger Kit
-A&A Secondary 8-rib Belt Drive System
-Innovators West 10% Overdrive Crank Balancer
-A&A 3.6" Supercharger Pulley
A&A Fuel System Single Pump Kit w/ Regulator And Stainless Braided Lines
-Racetronix 255 Intank Pump Upgrade
-Racetronix Fuel Pump Wire Harness
-ECS billet C5 fuel block for gas tank connection
Snow Performance Stage 2.5 Methanol Injection Kit
-Stainless Braided Lines
-Tig Welded Intake Bungs
Gauge
-Snow Digital Meth/Boost Pillar Gauge
-Autometer Analog Boost Gauge 0-15psi
-Autometer Dual A-Pillar Pod
-AEM wide-band A/F Gauge
Dewitts Radiator
Dewitts Dual Spal Fans
McLeod RXT Ceramic Clutch Kit
-McLeod Billet Steel Flywheel
-New GM Slave Cylinder
-New GM Master Cylinder
-Tick Bleeder
-ARP Bolts
WilWood 6 Piston Aero6 Brakes
-GM C6 Z06 Cross Drilled Rotors
-Wilwood Stainless Brake Lines
Aldan American Coilover Suspension
- 600LB Front / 550LB Rear-Track/ Auto-X
TPS Sway bars / End links / Polyurethane Bushings
HPI Driveline Solid Mounts
ECS Transmission & Differential Brace
Billy Boat Bullet Exhaust
Texas Speed & Performance Long Tube Stainless Headers
-Catless X-pipe
-ARP Header Bolts
Drivetrain
-GM T56 Transmission
*Hurst Shifter & Ball with Bronze Cup Bushing / C5 cnc solid mount shifter box bushings by Lucky Garage
-GM 3.42 Rear Differential
*New Output Axle Seals Replaced During Build Process
-GM Z06 Spec 12mm Driveshaft/Torque Tube w/factory GM Couplers
Wheels & Tires
-BC Forged RS45
19x10
19x11
-Nitto drag radials
Exterior
Functional side fender scoops by Electron sport
L.E.D. Halo Tail Lights
L.E.D. KnightdriveTV "Sleep Eye" Head Lights
L.E.D. Rear Laser side markers
L.E.D. 3rd Brake Light
L.E.D. Lastfit Fog Lights
Sequential Front Turn Signals
Hyper Flash Relay Harness Installed
*No wires have been cut or spliced. Plug and play adaptors used.
Interior
C7 seat conversion (Red Leather w/ less than 1K miles)
C7 sun visor conversion
Carbon Fiber Steering Wheel by Overtake
Nappa Leather shift boot / brake boot / center console w/red stitching
Alpine Custom installed stereo system w/ leather wrapped accents and plexiglass.
-2001 Corvette C5 with 27,000 original miles on car (300 miles on modifications)
874HP / 736TQ
Texas Speed & Performance 383ci Engine 10:1 compression
-TSP 230/242 .600 .600 114lsa +2 Cam (Engineered By "Pat G" for Application)
-Texas Speed Forged 4340 Crankshaft, 6-Bolt Flange
-TSP 6.125" Super I-Beam Forged Rods w/ ARP L19 Bolts
-Wiseco -15cc Dish Forged Aluminum Pistons
-Wiseco Tool Steel Wrist Pins
-Johnson 2110r Lifters
-Rollmaster Billet Timing Gear Set & Chain
-Melling oil pump 10296
-All new GM sensors / new GM water pump / all new GM seals & gaskets
-TSP Chromoly Pushrods
-ARP Main Stud Kit / ARP Head Stud Kit / ARP accessory mounting bolts / ARP clutch bolts
-Improved Racing C5 Corvette "Batwing Oil Pan" Crank Scraper
-FAST 92mm Intake w/ LS7 Throttle Body
-Stainless Braided Hose Steam Vent Kit For Cylinder Heads
-60lb Injectors
-Gen IV Engine Block w/ 24 Reluctor Wheel
-PRC 220cc "CNC" Heads, Flow 315 CFM Intake / 230 CFM Exhaust @ .650
*62cc, 2.045" Intake / 1.600" Stainless Valves, TSP .660" Dual PAC Spring
Kit, Ti Retainers, TSP 1.72" Roller Rockers w/trunion upgrade
A&A V3 Ti Trim Supercharger Kit
-A&A Secondary 8-rib Belt Drive System
-Innovators West 10% Overdrive Crank Balancer
-A&A 3.6" Supercharger Pulley
A&A Fuel System Single Pump Kit w/ Regulator And Stainless Braided Lines
-Racetronix 255 Intank Pump Upgrade
-Racetronix Fuel Pump Wire Harness
-ECS billet C5 fuel block for gas tank connection
Snow Performance Stage 2.5 Methanol Injection Kit
-Stainless Braided Lines
-Tig Welded Intake Bungs
Gauge
-Snow Digital Meth/Boost Pillar Gauge
-Autometer Analog Boost Gauge 0-15psi
-Autometer Dual A-Pillar Pod
-AEM wide-band A/F Gauge
Dewitts Radiator
Dewitts Dual Spal Fans
McLeod RXT Ceramic Clutch Kit
-McLeod Billet Steel Flywheel
-New GM Slave Cylinder
-New GM Master Cylinder
-Tick Bleeder
-ARP Bolts
WilWood 6 Piston Aero6 Brakes
-GM C6 Z06 Cross Drilled Rotors
-Wilwood Stainless Brake Lines
Aldan American Coilover Suspension
- 600LB Front / 550LB Rear-Track/ Auto-X
TPS Sway bars / End links / Polyurethane Bushings
HPI Driveline Solid Mounts
ECS Transmission & Differential Brace
Billy Boat Bullet Exhaust
Texas Speed & Performance Long Tube Stainless Headers
-Catless X-pipe
-ARP Header Bolts
Drivetrain
-GM T56 Transmission
*Hurst Shifter & Ball with Bronze Cup Bushing / C5 cnc solid mount shifter box bushings by Lucky Garage
-GM 3.42 Rear Differential
*New Output Axle Seals Replaced During Build Process
-GM Z06 Spec 12mm Driveshaft/Torque Tube w/factory GM Couplers
Wheels & Tires
-BC Forged RS45
19x10
19x11
-Nitto drag radials
Exterior
Functional side fender scoops by Electron sport
L.E.D. Halo Tail Lights
L.E.D. KnightdriveTV "Sleep Eye" Head Lights
L.E.D. Rear Laser side markers
L.E.D. 3rd Brake Light
L.E.D. Lastfit Fog Lights
Sequential Front Turn Signals
Hyper Flash Relay Harness Installed
*No wires have been cut or spliced. Plug and play adaptors used.
Interior
C7 seat conversion (Red Leather w/ less than 1K miles)
C7 sun visor conversion
Carbon Fiber Steering Wheel by Overtake
Nappa Leather shift boot / brake boot / center console w/red stitching
Alpine Custom installed stereo system w/ leather wrapped accents and plexiglass.
Last edited by C6-LS2-MN6; 03-08-2024 at 03:18 AM.
The following 12 users liked this post by C6-LS2-MN6:
Bobbo76 (09-18-2023),
DrFranzia (10-01-2023),
Eshoremd (09-23-2023),
f6john (09-18-2023),
Jason Blue Boost (10-04-2023),
and 7 others liked this post.
#3
Night Owl for life
Member Since: Nov 2003
Location: Bugs Bunny should'a made a left turn here
Posts: 23,247
Received 3,290 Likes
on
1,686 Posts
Post a pic of the whole audio system plz
The following users liked this post:
knewblewkorvette (09-17-2023)
#4
Instructor
Very impressive. Couple of questions.
Who was the supplier for the steering wheel, center console, shift boot, etc? Is the steering wheel a reduced diameter version?
What do you have for stereo speaker components and drivers?
Who was the supplier for the steering wheel, center console, shift boot, etc? Is the steering wheel a reduced diameter version?
What do you have for stereo speaker components and drivers?
#5
Burning Brakes
Thread Starter
RED STITCHING REAL LEATHER ARMREST LID COVER FITS CORVETTE C5 1997-2004 | eBay
****Keep in mind, most of the cost and labor is paying an upholstery shop to properly install it using small hog rings / staples / steaming the leather to stretch / glueing it / and trimming the edges.
RED STITCH LEATHER MANUAL SHIFT E BRAKE BOOT FITS CORVETTE C5 1997-2004 | eBay
Memphis Audio VIV60C at Onlinecarstereo.com
Entire system was built out of Birch hardwood. It's as light cardboard, but hard as a rock! Also, entire system was engineered on CAD and cut on a CNC machine..... not a single saw blade or jig-saw was used to make any part of the wooded pieces of the stereo system! I have an amp cover, but its not in the pics.
Last edited by C6-LS2-MN6; 09-17-2023 at 04:03 PM.
#6
Race Director
Member Since: Jul 2008
Location: The Sunshine State
Posts: 17,013
Received 2,688 Likes
on
1,487 Posts
2022 C5 of the Year Finalist - Modified
2021 C5 of the Year Finalist - Modified
C7 of the Year - Modified Finalist 2021
Finalist 2020 C7 of the Year -- Modified
2020 C5 of the Year Finalist - Modified
C5 of Year Finalist (appearance mods) 2019
2018 C5 of Year Finalist
Impressive build! Congrats. What I really like is that it’s a beautiful C5 sleeper and will surprise a lot of people on the road. Outside of the custom wheels and brakes, it looks completely stock.
The following 5 users liked this post by redzg:
Bobbo76 (09-18-2023),
Davcruz (09-18-2023),
DrFranzia (10-01-2023),
MAX3319 (09-18-2023),
Old School (10-21-2023)
#8
Burning Brakes
Sweet! Those wheels! I really like the stock thin spokes, have been looking for something close with no luck. Those however, they look like thin spokes on steroids! Beautiful ride! Love me a sleeper C5.
#10
Burning Brakes
Thread Starter
I will when I get a chance. Thanks
NO! C6 seats are nothing more than "updated" C5 seats.... Awful! These are C7 seats, very similar to a C8.
LINK to my other Z06 C5 w/ a C8 seat install for reference.....
https://www.corvetteforum.com/forums...te-how-to.html
Last edited by C6-LS2-MN6; 09-17-2023 at 05:20 PM.
#11
Le Mans Master
Member Since: Feb 2007
Location: Oviedo Florida
Posts: 8,823
Received 1,262 Likes
on
821 Posts
2023 C2 of the Year Finalist - Modified
2021 C2 of the Year Finalist - Modified
2016 C5 of Year Finalist
Looks great. Very nice. With that much HP you will need a lot more rubber. You will never hook like it is now.
Lets face it hot rods are never done.
Lets face it hot rods are never done.
#13
Melting Slicks
I like all your mods! I’m having trouble typing this post as I’m having to hold the keyboard at a distance to keep my slobber from messing things up. I think I’m going to sell my car so I can start gathering parts to imitate your build, wait, that won’t work! I am curious about the functional vents you speak of, that’s a new one on me?
#15
Le Mans Master
Member Since: Dec 2017
Location: Virginia
Posts: 5,379
Received 3,112 Likes
on
1,940 Posts
2021 C5 of the Year Finalist - Modified
St. Jude Donor '21-'22
DAMN! What is your primary use for the car? That's an awful lot of power for the street.
#16
Le Mans Master
Member Since: Dec 2017
Location: Virginia
Posts: 5,379
Received 3,112 Likes
on
1,940 Posts
2021 C5 of the Year Finalist - Modified
St. Jude Donor '21-'22
I like all your mods! I’m having trouble typing this post as I’m having to hold the keyboard at a distance to keep my slobber from messing things up. I think I’m going to sell my car so I can start gathering parts to imitate your build, wait, that won’t work! I am curious about the functional vents you speak of, that’s a new one on me?
#17
Administrator
Member Since: Mar 2001
Location: In a parallel universe. Currently own 2014 Stingray Coupe.
Posts: 343,891
Received 19,561 Likes
on
14,116 Posts
C7 of the Year - Modified Finalist 2021
MO Events Coordinator
St. Jude Co-Organizer
St. Jude Donor '03-'04-'05-'06-'07-'08-'09-'10-'11-'12-'13-'14-'15-'16-'17-'18-'19-
'20-'21-'22-'23-'24
NCM Sinkhole Donor
CI 5, 8 & 11 Veteran
You have put together a very nice ride - congrats.
#18
Burning Brakes
Thread Starter
I like all your mods! I’m having trouble typing this post as I’m having to hold the keyboard at a distance to keep my slobber from messing things up. I think I’m going to sell my car so I can start gathering parts to imitate your build, wait, that won’t work! I am curious about the functional vents you speak of, that’s a new one on me?
Corvette C5 - Fender Duct — Electron Sport USA
#19
Racer
Heroic build Sir! I have so much respect and appreciation for the the attention to detail and the all out exceptional choice of components. I really hope you're able to enjoy it for all the evident blood, sweat, and tears that went into it.
Also does anyone else smirk with he said "finished". I did then I looked through the pics. She's done. Nothing else you can do to that to make it better.
Also does anyone else smirk with he said "finished". I did then I looked through the pics. She's done. Nothing else you can do to that to make it better.