CorvetteForum - Chevrolet Corvette Forum Discussion
0 2018/12/25 06:54:35
0 2019/02/07 20:09:03
0 2019/02/07 20:09:20
0 2018/12/29 06:27:00
0 2019/02/08 06:22:44
0 2019/02/08 07:48:54
0 2019/02/09 09:45:38
0 2019/02/09 13:23:19
Big ass rotors
Big ass rotors
0 2019/02/09 14:53:35
Big ass wheels
Big ass wheels
0 2019/02/09 14:53:54
Big ass brakes
Big ass brakes
0 2019/02/09 14:54:15
Plenty of room! Everything is all torqued so I can put the front end on the ground and pull the engine/tranny this week.
Plenty of room! Everything is all torqued so I can put the front end on the ground and pull the engine/tranny this week.
0 2019/02/09 14:54:31
Wheel at ride height fits well. I thought the Wilwood brake kit would add 3/4” to each wheel, but no it is in almost the exact same place as the drums.
Wheel at ride height fits well. I thought the Wilwood brake kit would add 3/4” to each wheel, but no it is in almost the exact same place as the drums.
0 2019/02/10 13:59:51
I cycled the wheel from lock to lock and bumpstop to bumpstop to check for interference. I need about 1/4” at the rear edge of the wheel well which is currently unfinished and will be an easy blend.
I cycled the wheel from lock to lock and bumpstop to bumpstop to check for interference. I need about 1/4” at the rear edge of the wheel well which is currently unfinished and will be an easy blend.
0 2019/02/10 14:00:04
Anyone know if this is what is meant by the N11 off-road exhaust option? This car came with that option originally. I’ve now removed the entire exhaust (not original) in preparation for pulling the engine and tranny later this week.
Anyone know if this is what is meant by the N11 off-road exhaust option? This car came with that option originally. I’ve now removed the entire exhaust (not original) in preparation for pulling the engine and tranny later this week.
0 2019/02/10 14:00:26
0 2019/02/11 05:40:48
0 2019/02/11 05:41:12
0 2019/02/11 05:49:51
0 2019/02/11 08:11:47
0 2019/02/13 15:09:15
All that is left in the rear is to set pinion angle and bleed the brakes.
All that is left in the rear is to set pinion angle and bleed the brakes.
0 2019/02/15 13:09:50
One .030 shim in the bracket (baseline was two) No shims on the caliper (baseline was two)
One .030 shim in the bracket (baseline was two) No shims on the caliper (baseline was two)
0 2019/02/15 13:10:09
Can’t wait to see this at ride height. It is hanging by the coiliver which doesn’t allow it drop to the point that the ujoints bind. Nice feature!
Can’t wait to see this at ride height. It is hanging by the coiliver which doesn’t allow it drop to the point that the ujoints bind. Nice feature!
0 2019/02/15 13:10:24
Man, I have a messy garage!
Man, I have a messy garage!
0 2019/02/15 13:10:40
0 2019/02/15 13:10:53
Sorry for the shaky picture, I needed three hands!
Sorry for the shaky picture, I needed three hands!
0 2019/02/15 15:24:34
This is my new Dewitt’s radiator received yesterday with the same measurement.
This is my new Dewitt’s radiator received yesterday with the same measurement.
0 2019/02/15 15:24:46
0 2019/02/16 05:35:45
0 2019/02/16 05:35:52
Massive meats.
Massive meats.
0 2019/02/16 13:25:10
Perfect fit on the front (I will have to trim the front and rear bottom of the wheel wells for steering clearance).
Perfect fit on the front (I will have to trim the front and rear bottom of the wheel wells for steering clearance).
0 2019/02/16 13:25:32
And on the rear, although it is not on the ground yet.
And on the rear, although it is not on the ground yet.
0 2019/02/16 13:25:48
Once the engine is out, the front is going back up so I can paint the center of the chassis, replace the body mounts and run the fuel lines. Always something. In about a month it will be on four feet.
Once the engine is out, the front is going back up so I can paint the center of the chassis, replace the body mounts and run the fuel lines. Always something. In about a month it will be on four feet.
0 2019/02/16 13:26:16
Massive meats!
Massive meats!
0 2019/02/16 13:32:16
0 2019/02/16 13:32:33
I will have to trim and reshape the lower front and rear openings for the front wheels to have enough clearance for steering. Kind of important.
I will have to trim and reshape the lower front and rear openings for the front wheels to have enough clearance for steering. Kind of important.
0 2019/02/16 13:32:50
I think the rear will fit nicely also once on the ground. Unfortunately, that won’t happen for about a month.
I think the rear will fit nicely also once on the ground. Unfortunately, that won’t happen for about a month.
0 2019/02/16 13:33:18
There is about 4 1/2” between the tire and the rear wheel well edge. At ride height the wheel actually only moves back 1/2” which results in 4”.
There is about 4 1/2” between the tire and the rear wheel well edge. At ride height the wheel actually only moves back 1/2” which results in 4”.
0 2019/02/16 14:42:41
0 2019/02/16 14:43:04
There is about 4 1/2” between the tire and the rear wheel well edge. At ride height the wheel actually only moves back 1/2” which results in 4”.
There is about 4 1/2” between the tire and the rear wheel well edge. At ride height the wheel actually only moves back 1/2” which results in 4”.
0 2019/02/16 14:45:20