CorvetteForum - Chevrolet Corvette Forum Discussion
Radiator hose cut to fit.
Radiator hose cut to fit.
0 2023/12/08 19:04:33
Good fit to air cleaner. Might use a little longer hose, but works as is.
Good fit to air cleaner. Might use a little longer hose, but works as is.
0 2023/12/08 19:03:52
1/4" x 1" aluminum bar added.
1/4" x 1" aluminum bar added.
0 2023/12/08 19:03:33
Figured I would follow the instructions this time.
Figured I would follow the instructions this time.
0 2023/11/30 18:14:10
0 2023/11/30 05:20:23
PS front
PS front
0 2023/11/20 18:56:53
DS front
DS front
0 2023/11/20 18:56:36
Passenger's side
Passenger's side
0 2023/11/20 14:14:50
Driver's side
Driver's side
0 2023/11/20 14:14:17
Bonding strip LF fender
Bonding strip LF fender
0 2023/11/20 11:22:03
Bonding strip LF fender
Bonding strip LF fender
0 2023/11/20 11:21:46
0 2023/11/12 17:50:27
Not a Restomod, just fun in the sun or rain.
Not a Restomod, just fun in the sun or rain.
0 2023/11/06 09:01:03
Rag Tops are my flavor since 1965.
Rag Tops are my flavor since 1965.
0 2023/11/06 09:00:08
O-ring still loosely on the drift pin. Measure the O.D. Light touch needed.
O-ring still loosely on the drift pin. Measure the O.D. Light touch needed.
0 2023/11/04 14:42:36
O-ring fit loosely on a tapered drift pin or punch. Measure at the bottom of the O-ring and top and average the reading.
O-ring fit loosely on a tapered drift pin or punch. Measure at the bottom of the O-ring and top and average the reading.
0 2023/11/04 14:42:23
10 pin connector - 60s? engine harness.
10 pin connector - 60s? engine harness.
0 2023/11/02 14:16:42
Gen 1 Camaro door handle.
Gen 1 Camaro door handle.
0 2023/10/28 13:47:00
0 2023/10/01 05:33:08
0 2023/10/01 05:33:00
Original camber adjustment bolt / washer R66
Original camber adjustment bolt / washer R66
0 2023/10/01 05:21:37
0 2023/10/01 05:21:23
0 2023/10/01 05:21:07
GM Muncie 318 3 spd: Case: GM12 384522 C165 12 4 Tail Shaft: 2 3707195 4 bolt Cover: 3845044
GM Muncie 318 3 spd: Case: GM12 384522 C165 12 4 Tail Shaft: 2 3707195 4 bolt Cover: 3845044
0 2023/09/20 06:51:46
0 2023/09/20 06:38:24
0 2023/09/20 06:36:57
0 2023/09/20 06:36:56
0 2023/09/20 06:36:38
0 2023/09/20 06:35:49
I believe this is the stock tab for the accelerator spring on a 66 300hp / 327. Don't know if it is right for yours.
I believe this is the stock tab for the accelerator spring on a 66 300hp / 327. Don't know if it is right for yours.
0 2023/09/20 06:13:00
I disconnected the rear line at the distribution block and coupled it to a new line to the master cylinder. Then put a plug in the distribution block. I can easily revert back to the original master cylinder.
I disconnected the rear line at the distribution block and coupled it to a new line to the master cylinder. Then put a plug in the distribution block. I can easily revert back to the original master cylinder.
0 2023/09/20 06:12:58
Fond memories. Thinking about making end tables of them.
Fond memories. Thinking about making end tables of them.
0 2023/09/19 05:49:16
To reinstall the lock cylinder, align it in the position that you removed it, ACC and work it inward and then turn it back to OFF. Do not force it.
To reinstall the lock cylinder, align it in the position that you removed it, ACC and work it inward and then turn it back to OFF. Do not force it.
0 2023/09/10 18:10:26
This is the lock housing. If you magnify it, you can see the brass pin that you have to push in.
This is the lock housing. If you magnify it, you can see the brass pin that you have to push in.
0 2023/09/10 18:10:06
This is the key lock cylinder. Put the key in and turn it to the ACC position and you should feel the brass button with the paper clip in the small hole, then push the paper clip in and turn the key counterclockwise a little more and pull out on the lock cylinder.
This is the key lock cylinder. Put the key in and turn it to the ACC position and you should feel the brass button with the paper clip in the small hole, then push the paper clip in and turn the key counterclockwise a little more and pull out on the lock cylinder.
0 2023/09/10 18:09:56
The bulkhead connector is difficult to reach and can be broken if you get to rough.
The bulkhead connector is difficult to reach and can be broken if you get to rough.
0 2023/09/08 12:24:04
Jumper at the ignition switch connector with jumper wire. Battery disconnected to install jumper.
Jumper at the ignition switch connector with jumper wire. Battery disconnected to install jumper.
0 2023/09/08 12:15:58
If testing the ignition switch, you must turn the switch to each position to test the resistance.
If testing the ignition switch, you must turn the switch to each position to test the resistance.
0 2023/09/08 11:50:55
This upside down horse shoe is called Ohms for resistance measurements with no power on the circuit.
This upside down horse shoe is called Ohms for resistance measurements with no power on the circuit.
0 2023/09/08 11:49:51
This reading is zero Ohms indicating no resistance which is good.
This reading is zero Ohms indicating no resistance which is good.
0 2023/09/08 11:48:21