CorvetteForum - Chevrolet Corvette Forum Discussion
0 2023/05/10 18:53:38
0 2023/05/10 18:53:31
Also pay attention to the clearance between the tabs on the U-shaped contact at the back as it is hot 12vdc and if it contacts the housing it will short it out. Only about 1/32" clearance. I have no idea what it does.
Also pay attention to the clearance between the tabs on the U-shaped contact at the back as it is hot 12vdc and if it contacts the housing it will short it out. Only about 1/32" clearance. I have no idea what it does.
0 2023/05/03 14:08:25
Pay close attention to the tabs on the U-shaped contact inside the housing during reassembly, it must align with the slots in the housing.
Pay close attention to the tabs on the U-shaped contact inside the housing during reassembly, it must align with the slots in the housing.
0 2023/05/03 14:08:12
Another shot at a slight angle to help identify the orientation.
Another shot at a slight angle to help identify the orientation.
0 2023/05/03 14:07:46
I tried to orientate the components in the proper direction upon removal. Pay attention to that as you disassemble the lighter
I tried to orientate the components in the proper direction upon removal. Pay attention to that as you disassemble the lighter
0 2023/05/03 14:07:39
A true restoration challenge started 20+ years ago.
A true restoration challenge started 20+ years ago.
0 2023/05/02 05:23:03
You can see the threads on the housing and insert and how it screws together
You can see the threads on the housing and insert and how it screws together
0 2023/05/01 09:24:46
0 2023/05/01 09:24:38
female lug removed, you can see the tang on the back that holds the lug in the connector
female lug removed, you can see the tang on the back that holds the lug in the connector
0 2023/04/23 08:23:39
Small screwdriver or tooth pick or other to depress the tang while pushing the wire toward the screwdriver to insert it fully.
Small screwdriver or tooth pick or other to depress the tang while pushing the wire toward the screwdriver to insert it fully.
0 2023/04/23 08:23:28
Short wires sticking out, but there
Short wires sticking out, but there
0 2023/04/23 08:23:18
0 2023/04/23 08:22:03
0 2023/04/23 08:21:52
Can also be used to video trips and traffic, front and rear with the top down.
Can also be used to video trips and traffic, front and rear with the top down.
0 2023/04/17 18:49:22
Glued plastic under the magnet to prevent scratching the paint
Glued plastic under the magnet to prevent scratching the paint
0 2023/04/17 18:48:53
0 2023/04/04 18:29:11
Alumi-Blast and VHT clear coat.
Alumi-Blast and VHT clear coat.
0 2023/03/31 04:06:25
Are the ones on the bottom correct for R66?
Are the ones on the bottom correct for R66?
0 2023/03/30 03:59:45
Does this look better?
Does this look better?
0 2023/03/29 17:51:44
No matter where I got the decals, they wouldn't stick and stay.
No matter where I got the decals, they wouldn't stick and stay.
0 2023/03/29 17:51:39
0 2023/03/27 18:26:57
Not stock manifold, but bolts right up. I had to use the electric choke, but your divorced choke should work too with a little work
Not stock manifold, but bolts right up. I had to use the electric choke, but your divorced choke should work too with a little work
0 2023/03/27 18:26:44
0 2023/03/26 18:59:48
Just as I pulled them out, no filing or cleanup
Just as I pulled them out, no filing or cleanup
0 2023/03/26 18:59:30
Immersed carpet in bath of RIT dye.
Immersed carpet in bath of RIT dye.
0 2023/03/19 12:30:56
0 2023/03/19 12:30:44
RIT and Vinegar Driver's side
RIT and Vinegar Driver's side
0 2023/03/19 12:24:51
Completed carpet has a brown cast rather in the areas that were sun bleached. Will have to work for a while.
Completed carpet has a brown cast rather in the areas that were sun bleached. Will have to work for a while.
0 2023/03/19 12:21:11
RIT and Salt hand sprayed passenger's side
RIT and Salt hand sprayed passenger's side
0 2023/03/19 12:17:44
0 2023/03/18 19:10:43
0 2023/03/18 19:10:31
After removing about half the junk.
After removing about half the junk.
0 2023/03/12 18:56:25
0 2023/03/12 18:40:45
I don't know if this is called Jute underlayment or what?
I don't know if this is called Jute underlayment or what?
0 2023/03/12 18:40:18
This is the final Prototype installed. Does it look out of place?
This is the final Prototype installed. Does it look out of place?
0 2023/03/09 05:01:55
Ready to install.
Ready to install.
0 2023/03/09 05:01:44
Lining inside optional. I had to do it.
Lining inside optional. I had to do it.
0 2023/03/09 05:01:08
Simple lid with original "Butt Seat" foam and leather.
Simple lid with original "Butt Seat" foam and leather.
0 2023/03/09 04:59:50
Pop riveted to original pan and added a restraint to hook over the storage divider. No additional holes nor attachments to the body.
Pop riveted to original pan and added a restraint to hook over the storage divider. No additional holes nor attachments to the body.
0 2023/03/09 04:59:33