CorvetteForum - Chevrolet Corvette Forum Discussion
0 2017/05/17 16:39:02
0 2017/05/10 17:49:43
0 2017/05/10 17:48:53
0 2017/05/10 17:47:38
Yes staggered bolts
Yes staggered bolts
0 2017/05/08 19:22:13
Yes staggered bolts
Yes staggered bolts
0 2017/05/08 19:20:31
0 2017/05/08 08:46:13
0 2017/05/08 08:44:11
0 2017/05/08 08:43:25
The three short wiring leads plug into the main wiring harness. The three long leads plug into the headlight extension harness. And the two wires that were separated and I have to put connections on them will plug into the same spot as the long leads.
The three short wiring leads plug into the main wiring harness. The three long leads plug into the headlight extension harness. And the two wires that were separated and I have to put connections on them will plug into the same spot as the long leads.
0 2017/04/25 11:16:32
0 2017/04/25 10:11:18
65 repo base
65 repo base
0 2017/04/23 12:59:08
65 repo base
65 repo base
0 2017/04/23 12:58:18
Hitting float adjustment screws.
Hitting float adjustment screws.
0 2017/04/23 12:46:09
Sits up about 3/8"
Sits up about 3/8"
0 2017/04/23 12:45:09
0 2017/04/23 12:44:13
0 2017/04/23 12:43:18
0 2017/04/22 09:25:07
0 2017/04/22 09:24:30
0 2017/04/22 09:23:44
0 2017/04/22 07:36:26
0 2017/04/22 07:35:50
0 2017/04/21 17:09:40
Are these type of connectors available? So I would be able to use the factory plastic covers seen on the right with a heavier gauge wire.
Are these type of connectors available? So I would be able to use the factory plastic covers seen on the right with a heavier gauge wire.
0 2017/04/21 06:30:43
0 2017/03/31 07:30:30
Should there be a gap between the strut rod and the bracket?
Should there be a gap between the strut rod and the bracket?
0 2017/03/19 14:38:50
In all these pictures the frame sitting on blocks and the wheels are hanging.
In all these pictures the frame sitting on blocks and the wheels are hanging.
0 2017/03/19 14:22:35
Spindle supports are '67 parts, I checked the dates. To me it looks like the strut rods are too narrow for the spindle supports. The strut rods are '65 reproduction parts.
Spindle supports are '67 parts, I checked the dates. To me it looks like the strut rods are too narrow for the spindle supports. The strut rods are '65 reproduction parts.
0 2017/03/19 14:17:21
I was told that the inner strut rod bracket is off a C3 because it has this tab with the yellow arrow.
I was told that the inner strut rod bracket is off a C3 because it has this tab with the yellow arrow.
0 2017/03/19 14:13:52
0 2017/03/19 14:02:38
Inner strut rod bracket location
Inner strut rod bracket location
0 2017/03/19 14:00:27
Strut rod at inner strut rod bracket
Strut rod at inner strut rod bracket
0 2017/03/19 13:57:44
0 2017/03/14 19:41:59
Does anyone have a picture showing the internal parts of the steering shaft assembly? I am trying to figure out how the Locking device for the telescopic part works with the star screw and the rod going up the center of the shaft.
Does anyone have a picture showing the internal parts of the steering shaft assembly? I am trying to figure out how the Locking device for the telescopic part works with the star screw and the rod going up the center of the shaft.
0 2017/03/14 19:38:10
0 2017/03/14 19:35:10
Other side
Other side
0 2017/03/14 19:23:05
0 2017/03/14 19:22:17
Is this locking pin normally welded from the factory?
Is this locking pin normally welded from the factory?
0 2017/03/14 19:20:19
Other side
Other side
0 2017/03/14 19:12:31
0 2017/03/14 19:11:21