CorvetteForum - Chevrolet Corvette Forum Discussion
I have what looks like play in this pin. I assume this just goes through a hole in the lower shaft to the other side. I couldn't find schematic for the internal parts for the shaft assembly. But I am thinking the pin or the hole it goes through is worn out.
I have what looks like play in this pin. I assume this just goes through a hole in the lower shaft to the other side. I couldn't find schematic for the internal parts for the shaft assembly. But I am thinking the pin or the hole it goes through is worn out.
0 2017/03/14 18:54:22
0 2017/03/12 17:52:30
0 2017/03/12 17:50:31
0 2017/03/12 17:47:21
0 2017/03/02 16:58:07
0 2017/03/02 16:56:46
These bushings were replaced 45,000 miles ago. Should the tabs be bent over more? Are these not installed correctly or pulling out?
These bushings were replaced 45,000 miles ago. Should the tabs be bent over more? Are these not installed correctly or pulling out?
0 2017/03/02 16:51:43
1 " horn button spring
1 " horn button spring
0 2017/02/28 08:47:33
0 2017/02/20 05:35:38
0 2017/02/20 05:35:12
0 2017/02/18 05:50:52
3888948 C 28 8. Q.Jet . Was this used on a corvette?
3888948 C 28 8. Q.Jet . Was this used on a corvette?
0 2017/02/01 09:18:55
3866948 D 3 7. 325 & 350hp 396 chevelles. 427 390hp corvette?
3866948 D 3 7. 325 & 350hp 396 chevelles. 427 390hp corvette?
0 2017/02/01 09:14:48
0 2017/02/01 08:35:08
0 2017/01/08 18:33:31
0 2017/01/08 18:33:04
0 2017/01/06 15:54:01
0 2017/01/06 15:51:22
Is this the rounded boss
Is this the rounded boss
0 2017/01/06 15:49:22
'65 327 4spd. Built Nov '64. I would think this would be done at the factory, an error? It looks like the the 6 was flattened out and restamped with the 7. Serial # S101566
'65 327 4spd. Built Nov '64. I would think this would be done at the factory, an error? It looks like the the 6 was flattened out and restamped with the 7. Serial # S101566
0 2017/01/06 04:53:32
Drivers side serial # 4100111. If this is a corvette trans, should it not be 4S100111 or 4A100111?
Drivers side serial # 4100111. If this is a corvette trans, should it not be 4S100111 or 4A100111?
0 2017/01/06 04:11:58
Aug-15 ? What does the sideways 8 mean?
Aug-15 ? What does the sideways 8 mean?
0 2017/01/06 04:09:15
0 2017/01/06 04:07:01
Passager side speedo
Passager side speedo
0 2017/01/06 04:05:35
325 small shaft case
325 small shaft case
0 2017/01/06 04:03:22
Two holes filled under cross flag Fender emblems.
Two holes filled under cross flag Fender emblems.
0 2016/12/29 15:49:56
Two holes filled under Fender cross flag emblems.
Two holes filled under Fender cross flag emblems.
0 2016/12/29 15:48:00
This is the way it was when I bought the car. But I have seen pictures where are the regulator is further back beside the alternator on the inner fender. Also no holes in the rad support 4 the voltage regulator.
This is the way it was when I bought the car. But I have seen pictures where are the regulator is further back beside the alternator on the inner fender. Also no holes in the rad support 4 the voltage regulator.
0 2016/12/29 15:42:40
0 2016/12/29 15:40:58
4 more holes in passager inner fender. They don't line up for the voltage regulator, nor is there any voltage reg. mounting holes in the rad support at all. It's on the driver side inner fender. Where should the voltage reg be on what I assume is a '65 327 300hp non air car. Battery on drivers side.
4 more holes in passager inner fender. They don't line up for the voltage regulator, nor is there any voltage reg. mounting holes in the rad support at all. It's on the driver side inner fender. Where should the voltage reg be on what I assume is a '65 327 300hp non air car. Battery on drivers side.
0 2016/12/29 15:27:58
0 2016/12/29 15:17:28
Large hole behind ballist resistor.
Large hole behind ballist resistor.
0 2016/12/28 12:31:34
3 holes beside heater cover. Top hole has bolt in it. This car has aftermarket Vintage Air a/c.
3 holes beside heater cover. Top hole has bolt in it. This car has aftermarket Vintage Air a/c.
0 2016/12/28 12:26:15
65 327 4 spd. Firewall below heater. Yellow arrows. 4 - 1 inch holes. Red arrow. 1 - 1/4 inch hole.
65 327 4 spd. Firewall below heater. Yellow arrows. 4 - 1 inch holes. Red arrow. 1 - 1/4 inch hole.
0 2016/12/28 12:20:43
0 2016/12/28 11:49:12
65 327 4 spd. Clutch cross shaft.The frame side has a felt seal and the engine side has a rubber seal that was pushed out and distorted. I ordered new seals and recieved 2 felt seals. Does the engine side use both felt and rubber seal. Or do I get rid of the rubber one and just use the 2 felt seals? Dave
65 327 4 spd. Clutch cross shaft.The frame side has a felt seal and the engine side has a rubber seal that was pushed out and distorted. I ordered new seals and recieved 2 felt seals. Does the engine side use both felt and rubber seal. Or do I get rid of the rubber one and just use the 2 felt seals? Dave
0 2016/12/05 08:10:15
0 2016/11/30 15:32:58
0 2016/11/30 13:39:17
0 2016/11/30 13:38:37
0 2016/11/30 13:34:29